Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Rebuilding wheel cylinders
User Name
Password
lost password?   |   register now

Thread: Rebuilding wheel cylinders Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-19-2005 10:24 PM
Nightfire Well they come from the States, and I can only get them from the middle man (Dodge City Ontario) because the company in the states only does wholesales. Well Dodge City jacks the prices up so all I can do is pay up if I wanna play.

The rebuild went GOOD I'm excited, I should wrap the rear brakes up tomorow, got brand spankin' new brake shoes for $50 (all 4 for the back).
Honing the cylinders out was an easy job, the new rubbers fit good and the boots were good too. Go the new outer bearing installed now all I need to do tomorow is inner seals ( that'll suck though) and re-assemble everything. Then move onto the front...and then I can pass saftey inspection and I'll be rollin' in sytle down the road!!!




Mike
08-18-2005 11:58 PM
Mrwood
cylinders

I guess it is cheaper to get the kits. Hard to believe that they cost that much each. As long as they are not pitted to bad then you may be able to hone them out. Good luck on your project.
08-18-2005 11:35 PM
Nightfire New ones for a '50 Fargo---------$75 each (I need 4 for the back, 2 for the front)
Rebuild Kits for a '50 Fargo-------$14 each

My age: 17
profession: service clerk at a grocery store
wage: not enough




Mike
08-18-2005 10:19 PM
Mrwood
cylinders

Why not just put new ones on. I put new ones on my 48 chevy for just a few dollors more than what a kit would cost.
08-18-2005 09:18 PM
Nightfire
Rebuilding wheel cylinders

Hey gang

I'm gonna be rebuildling my wheel cylinders this weekend, I got the rebuild kit (pretty sure they gave me the wrong one). I'm taking the backing plate of tomorow and the wheel cylinder(s) (I got a split wheel cylinder deal on my '50 Dodge). My uncle will hone them out then. Is there anything I need to know before I do this? I suppose all it is is put the new rubber cups back in and re-use spring and piston right? Any special method of taking these out or putting them back in?



Just checking,


Mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.