Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Carb Spacer or Not?
User Name
Password
lost password?   |   register now

Thread: Carb Spacer or Not? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-28-2005 02:57 AM
IanRiordan If a spacer helps, then your carb or manifold is too small for your package, if it hurts too big. use a spacer as a tuning device. generaly if a four hole helps more than an open one the carb is too small and vice versa. Remember, comp, stroke, rod length etc play a major role in controlling air speed. Just use spacers to dial in your car, then make appropriate changes.... unless your class won't allow them.
08-24-2005 02:48 PM
66Caprice I found that with the Edelbrock, a 1" wood fiber laminate spacer really helped keep the carb a little cooler by reducing the amount of heat transfer going on.
08-24-2005 02:40 PM
Max Keith
To space or not to space

It all depends on what kind of spacer you are using. If you use a spacer with 4 throttle holes in it, this will tend to help your bottom and mid range power, with little or no help on top end, where a spacer with an open plenum, or big hole will tend to help your mid and top end, with little or no help to the bottom end.
The reason the 4 hole will help bottom end is that it keeps the velocity up at lower rpm, while the one hole jobs act to increase the size of your plenum chamber ( or chambers if you have a dual plenum intake), and large plenums are very useful for high end power increases.
The one with the one big hole, would probably have more effect on your engine, particularly on top end than the 4 hole variety would on your lower and mid range. The thing to be careful of is that while it may help your top end, the one holer may harm your lower end power. Its all a matter of compromises and what your desired end result may be.
08-24-2005 01:43 PM
Nightfire It might increase low end throttle response a bit, like I said they dont make a HUGE difference, just a small one. Most people wont even notice it.



Mike
08-24-2005 01:23 PM
Houston54 I will be running an edelbrock 2101 performer manifold and 1406 600cfm carb. This will be a daily driver. I doubt it helps with mileage but does it affect low end throttle response in some way?
08-24-2005 01:17 PM
1982 SS I have had good luck with one on a '64 with a nothing special 350. It is turning 13.49 with 3.73 gears and a higher than normal convertor. Your choice, I have one I will put on mine to increase plenum volume. I am for them when a better manifold cannot be easily had.
08-24-2005 12:11 PM
Nightfire Not all that much advantages or disadvantages. Your air picks up a bit more speed as it goes down into the intake and the spacer isolates heat between engine and carb. Nothing noticeable really.



Mike
08-24-2005 12:06 PM
Houston54
Carb Spacer or Not?

What are the advantages/disadvantages of running a one inch spacer under a carb. Clearance is not an issue in this case.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.