|09-12-2005 12:30 AM|
|Malibu73||Is that an Edelbrock Q-jet?|
|09-12-2005 12:03 AM|
I put my rebuilt quadrajet on today, and holy crap, a world of difference. It raps up a ton quicker, and does not miss a beat like the crappy demon that was on it. I did not get to drive it cause I did not get a chance to hook everything up, but I can already tell the difference. I can't wait to drive it!!! I will let you know if I can get it to do a burnout lol!
|09-06-2005 11:47 PM|
no kidding!!!!! holy cow...... at 8000 ft.....!
Will he give you any help?.. seems like he has it goin-on, as they say.
|09-06-2005 01:36 PM|
Those old heads need more timing. Try 40 degrees total.
Converter needs more stall
carb too big and running rich. richness kills torque. Install smaller jets. Get a holley 750 3310. Cheap and good running carb.
Really need better heads.
|09-06-2005 12:54 PM|
|sb72elcamino350||I was hoping for 14's because there is a guy at the track with a vortec headed 350, with a 3500 stall and 4.10 gears that will run a 14.0000 anytime he wants. He has a 69 Impala Car. So i was thinking that I would run as fast or faster then him. We have about the same size camshaft and everything! I need some super tuning!!|
|09-04-2005 04:39 PM|
|09-04-2005 04:09 PM|
Just a looser converter 2800-3000 and a 650cfm possibly 700cfm carb will make it come alive...
But one other question where is the 11.3 to 1 compression coming from...? What pistons...? Those 882 heads with the large valves work good together but they are large chamber (76cc)...
BTW if that is a Summit cam with those spec`s its the 1107 part number and with a stock converter it must be hell...?
|09-04-2005 01:00 PM|
|sb72elcamino350||Its a summit camshaft too. I got it to run on pump gas somehow, it stays super cool, does not get past 150-160 range. I would think it would beable to run in the 14's even here at IMSP in Montana, with a adjusted altitude of like 7000-8000 feet.|
|09-04-2005 12:44 PM|
Those cams will put the dynamic compression ratio so high that 93 octane fuel will probably not be near enough...... IMHO
|09-04-2005 12:39 PM|
Yeah i'm just using the stock converter till I rebuild the orginal tranny, because the tranny in it now has had a hard life, and I really don't see the point in filling up my better converter with crap when that tranny goes. I just barrowed the carb for the heck of it, and hated it its a 825 race demon. I just figured that it would have alittle more bottom end with even a stock converter, totally gutless. I have a remanufactered qjet that i am going to try with hopefully better results, i am much better at tuning quadrajets too. I had one other on there before but it would not even hold 3 psi of fuel pressure came out the top like a mad man. I built that thing to make alot of torque and hopefully I can get it out of it what I want. I tried to match the best I could with a very limited budget(18 years old student and a lube tech lol).
Thats me and the land bardge
|09-04-2005 09:26 AM|
I think the carb tune is OTL. Check your vacuum, size the primary power valve so the valve number is 2 less than idle vacuum. You probably can drop the jets down 2 sizes around. If you have sceondary power valve, use a 2.5 or plug it. You show total timing, the initial should be 12 to 16 depending on gas quality.
|09-04-2005 09:22 AM|
|ap72||The cam is a little big for the weight, however if you go smaller you'll run into detonation on pump gas, especially with ported iron heads. I think its a good engine, but you're utilizing it poorly. Adjust your timing curve so full advance scomes in sooner, get a better carb- perhaps one with a vacuum secondary around 700 cfm. And get a higher stall- you have to gears and the engine matched, but the stall converter is way out of line- go for around a 2800- 3200. That will allow you to take advantage of the rest of your setup. You built a braket engine and put on a braket rear end- don't try to make it streetable by using a smaller stall- use a midrange stall and setup your shift points to make it more street friendly (make them about 600 rpm after your stall speed).|
|09-04-2005 08:19 AM|
Well, let's see.............
A. Too much cam for the vehicle weight.
B. Too much carb for the vehicle weight.
C. Too much vehicle weight for the cam, carb and possibly motor. This is big block territory. The '69 Chevy wagons were killers in Super Stock but with a 427/390HP Rat motor.
D. Not enough converter for any of it.
|09-04-2005 06:58 AM|
|TooSlow||Those cam specs look suspiciously like the Edelbrock Performer RPM cam. This cam is notorious for being soggy on the low end. Replace it with a smaller modern grind, something like a Comp Cams XE262 or XE268 and feel the difference.|
|09-04-2005 06:22 AM|
|shine||you have a bracket motor. your power range is going to be 3k to 6500. getting a tune for the street is going to be tuff. big cam, big valves big carb = rpm. your best bet will be a small carb with a lean tune for street use. from there you will have to decide how much of one to give up for the other. street or strip. take your time and you'll get there. it's just really tuff to tune this type of set up for the street. see if you can borrow a 650 to start with and work up to what you want. most of your driving will be from idle to 4k. tune for that. you can always carry a big carb set up for play in the trunk good luck|
|This thread has more than 15 replies. Click here to review the whole thread.|