Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Lifter Valley
User Name
Password
lost password?   |   register now

Thread: Lifter Valley Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-10-2005 02:00 PM
Canadian Charlie Thanks Bumpstick and the others
09-10-2005 01:58 PM
Bumpstick Those holes are not for oil drain back... They are for ventilation more than anything... The timing chain or gearset is lubed mainly via the sump... Some oil may even sling off the chain and into the lifter area but it all drains back via the holes in the lifter area or the back of the block area... Just remember the engine should have a 2-3 degree slant to the rear... (gravity does the rest)
09-10-2005 01:23 PM
hause
lifter valley

Could It Be Because It Is A Dry Sump Block.
09-10-2005 01:20 PM
BigDawgsEatFirst Are u teasing us with these new parts.....LOL
Ha,Ha,
Pistons and block look good
09-10-2005 12:48 PM
Bad Rat 414 Those holes behind the timing cover should not affect drain back to the oil pan. I'd hate to think you had that much oil in the top side of your engine. The oil would have to be over 1 " deep. You also have holes over the top of the cam for drainage.
09-10-2005 11:23 AM
Blazin72 I just checked a block I had in my garage and the holes on it are much bigger and level with each other. Whether it matters or not I dont know There are lots of other places in the lifter valley for oil to drain back to the pan. I wonder if those holes in the front arent a for ventilation between the crankcase and the lifter valley or something? You know, so the oil will drain smoothly without bubbling back up. (you know, like leaving the vent closed on a gas can or on some oil drain pans)

I wouldnt think you should have to worry about them.
09-10-2005 11:09 AM
Jmark Don't really have a suggestion on the oil holes, but I had a hard time downloading the pic, its pretty huge. I copied it and resized it way down for the guys on dialup connections.
Mark

09-10-2005 10:21 AM
Canadian Charlie
Lifter Valley

My new GM Performance block showed up this week and I noticed that in the front of the engine at the oil drain back holes that they are not level so oil can flow out and back into the crankcase. Is this normal I didn't even check my old block before asking there is a lot of stuff on it? I know in the rear I should grind them open a little more.

Should I leave it as it is or get out my die grinder and open up the flow


http://www.photodump.com/direct/Cana...Picture028.jpg

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.