Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Hvlp Air Supply
User Name
Password
lost password?   |   register now

Thread: Hvlp Air Supply Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-16-2005 10:47 AM
oldred Fitting size does matter, a lot in fact, regardless of which side of the regulator it's located. I ran into this recently with a cheap gun regulator(diaphragm type) that, although it regulated the pressure just fine, it has a bore of quite a bit less than 1/4" at the smallest point and will simply not flow enough volume. The fittings MUST be big enough to flow what the gun requires.
09-16-2005 07:53 AM
shine any paint supply will have them. i don't pretend to be smarter than the folks that designed these guns. i use iwata guns and follow their advice . my paint booth is set up for hvlp. i shoot at 10 lbs and have no problems. many painters have bought these new guns but are having fits with them. fittings and regulators are a lot of the problem. my old binks reg/trap was pretty much useless under 20 lbs. iwata , sata and most other suppliers have useful q&a web sites with professionals to answer your questions. i would recommend going there with your paint questions. hub on the ASET web page is really helpful. he's known as Dr Gun good luck.
09-16-2005 07:49 AM
fitzwell ...yeah, but you gotta GET it there, big bore fittings available @ your local Napa
09-16-2005 07:24 AM
milo by the time it gets there it can't matter
09-16-2005 07:05 AM
jcclark Can you reccommend a place I can buy these HVLP fittings?
09-16-2005 05:57 AM
shine hvlp fitting have a larger hole for more air flow. same with regulators and cheater valves.

the small stuff is the difference between doing it right and just getting by. check your facts, i'm not a spectator.
09-15-2005 07:15 PM
milo
Quote:
Originally Posted by Kampr
I've never had anything hvlp. Are the fittings not interchangeable or is there some other reason to use them? Thanks for all answers.
Don't worry that came from behind the dugout... don't sweat the small stuff..
of course they are interchangeable..
09-15-2005 06:58 PM
Kampr
Quote:
Originally Posted by shine
be sure to use hvlp fittings on your air lines.

I've never had anything hvlp. Are the fittings not interchangeable or is there some other reason to use them? Thanks for all answers.
09-15-2005 05:36 PM
shine be sure to use hvlp fittings on your air lines.
09-15-2005 03:21 PM
oldred Kampr, That should work just fine but be sure the electrical circuit can handle both compressors. If they both kick on at the same time it could add up to a huge AMP draw and trip the breaker if they are on the same circuit, not a nice thought if you are half way through the paint job.
09-15-2005 02:50 PM
J Cal I'm no expert, but that's what I did when I painted my car. I had a craftsman 5 hp 25 gal compressor and borrowed a simmilar one off my brother and linked together like you suggested, they just barely kept up. Because they were both running constantly the air comming out was pretty hot and moister would pass right through my water trap. I ended up solving this by buying a 50' length of that cheap plastic air line, left it coiled up and put it in a 5 gal pail of ice and water. I put this setup between the output of my compressors and my water trap and it solved my problem. My next big purchace for the garage will be a "real" compressor. Good luck!
09-15-2005 12:42 PM
Kampr
Hvlp Air Supply

I'm going to buy an hvlp paint gun soon. Problem is that my compressor is only 8.5 cfm. I don't have to have a bigger compressor for other uses but would for this paintgun. I may buy a bigger compressor in the future but not now. My question is, if I borrowed a compressor comparable in size to mine and connected them together with a T on the outgoing pressure lines would that work? Two 8.5's together should be 17 cfm? Has anybody done this before?

Thanks
Danny

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.