Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 8" Ford Rear info.Wanted.
User Name
Password
lost password?   |   register now

Thread: 8" Ford Rear info.Wanted. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-16-2002 02:14 AM
Barry.M Thanks for all the info.. I appreciate the help,especially crawling under cars to get the measurements !!!. I have checked out the link and it has answered a lot of questions.
Cheers...........Barry.
08-15-2002 12:13 PM
dmorris1200 Pretty good there lamothe1, if you check the link I posted a few posts back you'll see it should be 52 inches for the 65-66 mustang. At 52 1/2 you were just about on the money. We all should be able to measure that good with a flashlight.
08-15-2002 11:28 AM
lamothe1 barry, I meant from housing flange to housing flange where the backing plates bolt on
08-15-2002 11:26 AM
lamothe1 Barry, I measured a 8" in my back yard and it measures about 52 1/2" from axle flange to axle flange. it came out of a '65 mustang. (it could have even been 52 3/4" seeing I was measuring it in the dark while trying to hold the tape and flash light at the same)
08-15-2002 04:42 AM
dmorris1200 Yea I was surprised myself. I swapped over the backing plates with brake hardware and axles. You can see a pic of the operation in my photo album. I left the backing plates hanging while I swapped over the housing. The 9-inch I got was also out of a mustang same as mine which helped cause I didn't have to modify anything.
08-14-2002 09:39 PM
juxtoposed I thought that they might be, the new 7.5 and 8.8 ust the ssame axles and backing plates but I did'nt know aboput the older stuff. Good to know. thanks.
08-14-2002 10:47 AM
dmorris1200 When I swapped out the 8-inch for a 9-inch in my mustang I actually used the axles from the 8-inch rear. They were exactly the same.
08-14-2002 03:51 AM
Barry.M Thanks for your inputs,dmorris1200 & juxtoposed.
Yes I agree that 2 1/2" standoff would be arround the mark. This would bring the measurement up to 57 3/4 which is getting too wide for this project.

I'll keep looking,there's a swapmeet coming later this month,you just never know what you will find.

Thanks for your time.............Barry.M
08-13-2002 11:27 PM
juxtoposed It seems to me that on a 9" the axle standoff that all of the popular brake kits use is 2 1/2". Axle stand off is the distance the axle sticks out of the housing. So if you add 5" to your width that gets you close. Maybe someone else can tell you if 8 and 9 inches are the same in this respect. Good luck.
08-13-2002 06:13 AM
dmorris1200 Hi Barry, don't know if this will help but I got this link a while back.
<a href="http://www.ridgenet.net/~biesiade/Fordrears.html" target="_blank">www.ridgenet.net/~biesiade/Fordrears.html</a>
08-13-2002 01:39 AM
Barry.M
8" Ford Rear info.Wanted.

I am currently collecting parts etc. for our '27 T Roadster project. Being a light 'Rod I have stumbled upon an 8" Rearend,Housing only ,NO AXLES or Brakes etc.,(plus a 3.00 gear centre). The housing measures 52 3/4" wide. What I would like to know is its overall width Axle to Axle or Drum to Drum. Also,any idea what it might be out of from my very sketchy info.. I need something arround 56" O/A width.

The owner has had it for many years and can't remember what it came out of. As I'm not too familiar with Ford stuff, I thought I would come to the Experts !!!.

What I do know is that these Rear Ends when supplied in Australian Built cars (1967-1970 Ford Falcons and Fairlanes) were arround the 58-59" wide(Drum to Drum). But I don't have one to measure the Housing width.

Any help would be appreciated.........Barry.M

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.