Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> whats a governor??
User Name
Password
lost password?   |   register now

Thread: whats a governor?? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-19-2002 09:08 PM
1984camaroZ28 alright just checking to make sure
10-19-2002 04:30 PM
JdOwNj The guy that told you this didnt make sense.... im not seeing any way that what he said could apply to cars...
10-18-2002 08:49 PM
1984camaroZ28 are you saying i don't make sense or the guy that told me this don't make any sense.
10-18-2002 04:44 PM
JdOwNj To turn it into a full manual, The governer is no longer needed, as is not the kickdown linkage, modulator, etc, but a special valvebody is needed. What this person is talking about rremoveing is a governer on the engine, a speed limiter, these are confined to small engines and tractors, etc, doesnt apply to cars. Newer computer controlled cars have an electronic governer that retards timing and/or shuts off fuel to kkep you under a certain speed, this is 90 and up model years... No matter how you look at it this guy doesnt make sense...
10-18-2002 02:45 PM
willys36@aol.com Don't know.
10-18-2002 01:25 PM
Maverick Is that what I have heard some drag racers take out to make it a manual transmission with no clutch?
10-18-2002 01:13 PM
1984camaroZ28 thanks allot guys, i guess i shouldn't believe that guy anymore,
10-18-2002 12:38 PM
willys36@aol.com Governors are very simple devices on Auto transmissions. As BestMech says, it is just one of several inputs the trans needs to do it's job properly. Remove it and the trans can't do anything 'cause it has no information.

They are located on the tail shaft and consist of a couple of spring loaded weights that are connected to a slide valve in the fluid control circuit. It is a 'speedometer' for the trans, i.e. the slide valve is all the way in when the car is not in motion but as the car takes off and gais speed, the weights are thrown out by centrifugal force, overcome the spring tension, and move the slide valve proportional to the speed of the car. Thus the transmission has the information it needs to change the shift points and severity for optimal shifts. People who know their stuff play with the size of the weights and spring tension to get the shifts they want, just like you do with the centrifugal weights and springs in an ignition distributor. The typical hobbiest or racer needn't worry about the governor except be sure the springs aren't broken and the slide valve works freely.
10-18-2002 11:29 AM
BstMech To save a lot of typing, it (along with the modulator/kick-down/TV cable) tells the trans when to shift up/down. Leaving it out won't allow it to shift, in fact it won't work at all. I believe they were talking about removing the "accumalator" spring, this will make it shift "hard" at all speeds (very annoying for a daily driver). Maybe someone (KULTULZ especially) can provide you with a link to learn a lot more about this subject. The Internet is sooo cool!

[ October 18, 2002: Message edited by: BstMech ]</p>
10-18-2002 09:03 AM
1984camaroZ28
whats a governor??

i know engines pretty good but when it comes to transmissions i'm lost. my question what is a governor, whats it for. somebody told me once that taking the governor out helps performance is this true?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.