Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> DuPont URO 110xS Primer-Filler
User Name
Password
lost password?   |   register now

Thread: DuPont URO 110xS Primer-Filler Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-05-2005 09:25 PM
Scode68
The stuff is hard to sand

I blocked the roof for over four hours with 400 last night and all I was able to do is knock most of the texture off of it. I used the 1104 in the past with a conventional gun, which is a medium gray and it sands fairly easily. Now I switched to the 1107, which is a dark gray, and I applied it with a HVLP gun. The darker stuff seems harder than the lighter colored stuff to sand. I switched to the darker color because I plan on using a dark base coat. Could it be the URO, types of activator or reducer, or maybe something atmospherical?
11-04-2005 03:07 PM
Scode68 Thanks Barry,

A little extra traducer did the trick. The stuff I just shot today has the same texture as the stuff shot with the regular gun.

11-04-2005 06:30 AM
BarryK Most likely your problem is the scfm.
Make sure the air regulator at the wall is wide open and do all your adjusting at the gun.
wall regulator should read 100+ pounds.
Than adjust your gun regulator to what you want .
This will get you more scfms and break the paint up better.

The offshore guns we just don't know how accurate their scfm ratings are.
11-03-2005 09:32 PM
Scode68 I adjusted the fluid and played around with the air pressure but I only went up to 40. The best I could shot was at two turns of the needle and about 33 PSI at the gun. I thought that maybe I wasnít getting enough cfm but my compressor is rated at 8.2 cfm @ 40 and the gun will work in the 7-9 range @ 40 psi. I did hook the compressor up to a pipe system that is ĹĒ and Iím running it through one of those large high flow desiccant air filters but I thought that would only help me. What I wound up doing was hitting it with a green scotch pad to chop down the high point and then I was able to sand it fairly easily with 400 grit. I think if I waited a few days it might have been harder sanding. I tried out an area on the taillight panel that I shot back in May with the other gun and it was still easier than what I just shot.

This is the gun

I sprayed with the self-etching Vari-Prime with no problem. Iím going to try more reducer next time.
11-03-2005 08:59 PM
BarryK Its a very good primer.
Normally it sprays a little grainy more so than orange peeley.
A lot of 2K primers tend to spray with a slight grain look.

If it is orange peel, I would start by adjusting your fluid adjustment in a couple of turns and you may need another 5 to 10 lbs of air pressure at gun.

If not of that works see if they allow you to add a couple of ounces of urethane reducer.
11-03-2005 04:14 PM
Scode68
DuPont URO 110xS Primer-Filler

Anybody using DuPontís URO Primer-Filler with good results? Iím not sure if itís the new HVLP gun I bought but no mater what I do, I get orange peel. It didnít seem too bad with the conventional siphon gun I used in the past.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.