Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Cut and Buff Single Stage paint
User Name
Password
lost password?   |   register now

Thread: Cut and Buff Single Stage paint Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-05-2005 10:45 PM
x711 Hey guys, thanks for the reply, and best of luck on your paint jobs.

I was looking to use the Presto line of products as they look good to me.

http://www.prestaproducts.com/

I have never painted a Car before so this is my first cut at it. I shall
try post pics when its complete.

The Valspar Paint seems to set up very well and has got nice DOI
even without cutting and buffing. My cut and buff will mainly be to
remove the nice little dust particulas that I am sure will make there
way into the paint Oh for a a real down draft spray booth !, like in my
dreams.

Thanks .... X
11-05-2005 11:43 AM
crashtech 3M Perfect-It 3000 Rubbing Compound #6062 can be used with a wool or a foam pad, and is a bit more aggressive than the product you chose. It's what I would use for a complete job, since my back is not that good and I like to get done already!
11-05-2005 11:24 AM
roger1
Quote:
Originally Posted by crashtech
I'm interested to see how this works on a complete vehicle. The catalog states that this product will remove 3000 grit scratches, but also says that it's "Ideal for spot/small repair areas", which indicates to me that you might be there for an extended period with the buffer.
Yea, I knew that when I bought this stuff but I wanted to avoid going to the wool Superbuff pads. I've had trouble in the past getting a few scratchs using wool pads although they were Schlegel brand not the 3M.
A few on this forum have indicated that using the foam pads results in no scratches. Is there an alternative to the Perfect-It III Machine Glaze that you think might work better?
Some more buffing time with the Machine Glaze wouldn't bother me as long as it doesn't turn out to be a P.I.T.A.
11-05-2005 10:30 AM
crashtech
Quote:
Originally Posted by roger1
...4. Perfect-It III Machine Glaze (05930) with a polisher and 3M foam pad...
I'm interested to see how this works on a complete vehicle. The catalog states that this product will remove 3000 grit scratches, but also says that it's "Ideal for spot/small repair areas", which indicates to me that you might be there for an extended period with the buffer.
11-04-2005 10:24 PM
roger1 Well, that's what I'm starting to do right now only with PPG Global DG Single Stage.

This is what I am planning on doing:

1. Block by hand with 1000 wet.
2. Block by hand with 1500 wet.
3. Use 3M Trizact 3000 foam pads on a DA wet.
4. Perfect-It III Machine Glaze (05930) with a polisher and 3M foam pad.
5. Perfect-It III Finishing Glaze (05941)with a DA and 3M foam pad.

I have never done it this way before, so I hope it works well. All this stuff was outrageously expensive at the local Sherwin Williams store. Should have shopped around on the net for it.
11-04-2005 02:19 PM
x711
Cut and Buff Single Stage paint

Hi all, After I complete my paint job I shall be color sanding. Do any
of you have any hints or tips for cut and buff on single stage paint.

The paint I am using is Valspar Omega 2K

Thanks X.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.