Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Will An Olds 455 Engine Fit In My 69 Firebird
User Name
Password
lost password?   |   register now

Thread: Will An Olds 455 Engine Fit In My 69 Firebird Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-11-2005 01:38 AM
jimfulco The subframe of the '67-'69 Firebird is basically the same as the '73-74 Olds Omega, which, I believe, was available with an Olds 350 engine. The motor mount position on the Olds 350 is at the same place as on an Olds 455, so you may be able to use the mount system from an Omega with an Olds 350 to mount the Olds 455 in the Firebird subframe.

The '69 Firebird used a metal frame bracket with a rubber & metal mount sandwiched between it and the engine. On the Omega, a solid metal bracket was attached to the engine, and a rubber & metal "clamshell" mount went between the frame & that bracket. The bolt holes in your frame might not be in the right position, but you can drill your own if you need to.

The 455 has a taller deck than the 350, so accessory brackets from the 350 probably won't fit the 455, and you might run into some interference since the 455 is a little wider. It might be easier to just sell the Olds 455 or see if you can find someone with a Pontiac 455 that's willing to swap.
11-10-2005 10:12 PM
techinspector1 "As the steering box gets in the way."

Of course it'll make it tougher to fit passenger side exhaust, but you can move the motor/trans to the passenger side slightly to get some clearance if you need to, just be careful about keeping the centerline of the crank parallel with the centerline of the car to prevent u-joint problems.

On a 302 Ford / 83 Mitsubishi truck swap i did, I moved the motor-trans to the passenger side of the truck 2 1/4" to clear the box.
11-10-2005 08:36 PM
BOBCRMAN@aol.com The subframes on the post 69 Camaro/Firebirds are front steer like the Chevelle and GtO frames. So you may have to fabricate frame mounts for the early rear steer frame. A 455 Olds will fit. As mentioned you will need an Olds compatible trans but any BOP 350/400 turbo should fit. exhaust manifolds or headers might be tuff to find also. As the steering box gets in the way.

I have done 500 Caddys in this combination with nearly all factory parts.
11-10-2005 08:28 PM
techinspector1 My son and I put a 455 Olds in a 72 Luv truck for his high school driver, but I've never put one into a Gen1 Firebird. Here's some info I came across, hope it will help....
http://www.442.com/oldsfaq/ofswp.htm...ine%20Swapping
11-10-2005 08:27 PM
woodz428 Unless you have a bell housing for the Olds pattern, that will need changing. I think that the 403 Olds engine (called a corporate engine at the time) was available in some mid to late '70s 'birds, so you should be able to get motor mounts and other parts to set it right in.
11-10-2005 08:17 PM
daveh
Will An Olds 455 Engine Fit In My 69 Firebird

Hey guys,

I just bought what I thought was a pontiac 455 for my 69 Firebird but what I got was a 455 oldsmobile engine. I know I should have done my research. Anyway I got it and my question is will it fit ok? Do I have to make any unusual modifications? Any help on what to do is appreciated. Thanks

Dave

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.