Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> which one is right?
User Name
Password
lost password?   |   register now

Thread: which one is right? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-15-2005 07:46 PM
2112jb update!!!!!!!!!!!
i ran with the set up in picture number 3, as it made the most sense. it works great.
just a foot note: i also bought the self bleeders from (help), man i had never used these things and i want to tell you they are great. i had the system bleed in less that 10mins. those things are awesome. i just used a piece of rubber hose over the bleeder valve and ran it into a coke can. no mess!!!!
11-14-2005 01:34 AM
elliott The third one looks right to me.

I put a '67 MC on my '66 Mustang and a '70-ish prop valve. The third one looks closest to what I did. The switch on mine was pointing up, the lines went from the MC into the top of the block.

I will try to get a pic of my setup for you tomarrow. It works fine for me, I just upgraded the MC to a dual for now, the Granada spindles are going on soon.
11-13-2005 01:07 PM
67 Deuce 4 Me I also agree the third one "looks" right. But like what was already said, I would look at a known good set up.
11-13-2005 11:37 AM
yesgo Definitely look at a few untouched cars, and a service manual, to be sure. Ford used that same valve body for a # of years. (The earlier ones had 2 additional ports for an inline res. valve to rear.)

To me, the third one (without master) looks most likely to be correct, with the inlets on either side of the wire. The front inlet might be supposed to be on the end (where driver's front connects), rather than top, but I see them both ways. I also usually see them mounted flat, with the wire coming out the side, rather than top.

The other 2 just look wrong, both from the mounting rotation and line inlet aspect. Inlet lines wont normally enter from opposite sides, unless it is from either end (front and back of valve), which is not possible on yours. They either will enter from same side, next to the wire, or one next to wire, and the other on one end.
Those two also have an inlet on the bottom, and outlet on top. This goes against gravity, and could make it more difficult to bleed all the air out.
11-13-2005 07:27 AM
302 Z28 I'm with you Deuce, I think I would go to the local Ford dealer and look at a shop manual for a brake diagram.

Vince
11-13-2005 01:14 AM
Deuce As a Moderator, I have watched this question with interest.....I guess no one knows for sure.....I sure do not...

11-08-2005 12:10 PM
2112jb
which one is right?

i am doing the granada swap. i have found conflicting info on brake line hook ups. note that in one of the attached photos the valve is backwards, but the lines are still in different places.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.