|11-05-2006 12:08 AM|
When picking a air gun don't forget
Yes, A very good point...Buy the better unit. Everyone makes a generic air gun, but if you depend on your tools to put food on the table then buy the best you can afford and upgrade when you can afford better. Then take care of them and they will give you the service you want.
|11-04-2006 08:49 PM|
impact air tool
I don't know if you have bought an impact, but I have the IR twin hammer 1/2 in. impact with 450 ft.lbs forward and 730 ft.lbs reverse .I work in a machine shop and have used it almost daily for about 4 years . Its small , lite weight and does a great job. Would not go to work without it. It will cost a little more but its worth it.
If I get another one I would go to the next level up, it has 1000 ft. lbs in reverse.
another thing, only use a good air tool oil in it and use it ofter. Always lube your tool.....
|03-20-2006 07:28 PM|
I'll add some more info too-
Since I last posted in this thread,I bought a Chicago Pneumatic 724 3/8" impact. I've used it on a few jobs and I'm wondering why I waited so long to get it. The gun is compact,light and has plenty of power. I used it once to pull SBC heads off a few dead soldiers trying to find the best cores for rebuilding. The gun did this task well,had plenty of power and saved a lot of time. For anyone considering a 3/8" gun,put this one on the list to check out.
|03-20-2006 06:50 PM|
|oldred||May be an old thread but that is fresh, and good, info|
|03-20-2006 06:45 PM|
|oldschoolrods||I realize this is an old thread but after working with my new Matco MT1769 for a while I will post my review, for the money this gun is awesome, I have not had a bolt yet it would not break loose, soon I hope to try it on some head bolts to really test it out. But if anyone is looking for a good light 1/2 impact this is a good one. Thanks again|
|12-15-2005 07:28 AM|
From the point of view of working in a heavy duty truck dealership, I would buy a 3/8 and a 1/2" impact. All the heavy truck shops that I have seen
provide 3/4 and 1" impacts. There is no way you can get away with a 3/4 or just a 1/2 and adapt it down. Now let me explain. There are too many places on a truck that are close quartered with the new emissions engines and aerodynamic body styles that a 1/2" just will not fit in. Heck, you can pretty much put a Detroit series 60, Cummins,Cat etc........back together with a 3/8 drive impact.
A lot of good info has already been posted by others here! I would buy these two and stick with a good known brand. You will develop your own opinion after working with tools day in / day out.
|12-14-2005 09:35 PM|
adapters they work for me a long time,still do....rodhead
|12-14-2005 09:29 PM|
When picking a air gun don't forget
You want to get the rest of the story so to speak. I would recommend a long whip hose with a swivel at the gun. Put a coupler on the air feed hose that has a guard to prevent it from being un-coupled if it catches on anything. Rule one .... don't lend it. Rule two .... keep it clean. This means oil it with a quality air tool oil EVERY day and keep moisture out of it even if you have to buy your own water trap. Rule three ... don't crank it up to the max unless the fastener just refuses to move. Fast Orange made a great point...You might be side of the road trying to get it off. As 302/Z28 observed not everything should be driven down with an impact. You can tighten lug nuts with an impact provided you use a torque stick and set the impact to the proper setting. ( bet most techs have no idea what is involved in doing that) But if you don't want to spring for the expense of the torque sticks you will need a good torque wrench any way (be sure to buy wisely there also). Hope this helps.
|12-12-2005 02:44 PM|
|oldred||Redrod, Can't get that link to work but if you are talking about the one I think you are(from Snap-On) they are fantastic!|
|12-12-2005 01:32 PM|
Re:What size impact to get
I`d recomend this one:
|12-02-2005 06:01 PM|
for 3/8 drive I primarily use a air ratchet I have several the bad boy of the bunch (when I say the bad boy is the model i've seen used in the bone yards the most with the least amount of complaints)
is the Snap On FAR 72B with good air pressure hold on it will hurt you (I 've knocked a couple of finger nails off with it)I have 3 of them
for repetitive tasks such as putting deck screws through a plank on a trailer i have a 3/8 pistol grip impact Husky
easier to control than a butterfly
I have a elcheapo 1/2 impact for light stuff that I think might break and the I R 231 double anvil
that double anvil comes 3/8 1/2 & 3/4 that I know of the most impressive impact (to me ) ever !!that double hit really does the job
harbor freight by me sells new IR's and CP's as far as I can tell there is NO difference between central and chicago pneumatics if you put them side by side and took off the stickers I cant tell the difference
i bought a Chicago 3/4 drive impact wish i'd bought the IR
now as far as sockets that also depends on how much you are gonna use them my 1/2 is S-K and they are damn tough for what I use them for.
I'm not prejudice, I hate everyone
|12-02-2005 10:56 AM|
|12-01-2005 07:42 PM|
Added to Hotrodders Knowledge Base
This discussion has been added to the Garage - Tools Discussions category of the Hotrodders Knowledge Base.
--For the main page of the Hotrodders Knowledge Base, click here.
--For more information on the Hotrodders Knowledge Base, click here.
--For information on becoming a Hotrodders Knowledge Base Editor, click here.
|11-29-2005 02:43 PM|
get one off these ingersolrand airguns they are spot on, if you get there 3/4 gun you will be stripping nuts and bolts.
you will only need the 1/2inch one if you are doing cars ans vans
|11-29-2005 02:13 PM|
I have decided to get the MT1769 from matco, http://www.matcotools.com/Catalog/to...select=&page=4
I borrowed it from a friend of mine and it was one powerful gun plus a 2 year warranty, and with my votech discount it was $100 off. Thanks everyone for all their input.
|This thread has more than 15 replies. Click here to review the whole thread.|