Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> the rear section of a 31 chevy 5 window coupe
User Name
Password
lost password?   |   register now

Thread: the rear section of a 31 chevy 5 window coupe Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-03-2005 10:35 AM
46chevyfleetline Try checking the dimensions of a s10 frame.They pretty good on the mid 30's chevys. Just a thought.
12-03-2005 07:51 AM
baddbob I'm sure there's got to be some sheetmetal around the Northern California area for this project, anyone here got any parts this guy can use???????
Even if they're just for mockup... Bob
12-03-2005 07:48 AM
baddbob WOW, you aren't starting with much there! I don't have the measurements you're after but if I were were you I think I'd research buying a replacement lower panel to establish the rear body width or you could also just find or buy a replacement decklid to establish the rear body width. Once you know where the quarters need to be spreadwise then you can cross measure the top in several places throughtout the length of the body and also cross measure the floor area to keep everything is squared up then start making the parts that are missing...hope that made sense. Work the project directly on the floor if it's flat and level or consider building a temporary table, trying to do it on a frame is going to be a PITA. Once you've got all the sheetmetal squared up, braced, and fitted then move it to the frame and construct the floor. Just some suggestions.
I've got the rearend of a 29modelA coupe and the front of a late 20's Whippet that I've been thinking about putting together- I did a quick cut and mocked them up together and the lines actually come real close to perfectly aligning with better proportions than a stock A coupe, metal condition is just a bit better than yours judging from your pics. All I need is more time, someday....
Good luck with the project, hang in there cause it's going to be a long road. Bob
12-02-2005 11:25 AM
h0trod389
the rear section of a 31 chevy 5 window coupe

i picked up a car a month ago as a pile of parts all stacked on top of eachother.
the cowl are from a 1930 olds, the rear section is a 31 chevy 5 window coupe.
can anyone give me a couple of dimentions so that i can build the rear body frame?

i need:
1, the tail pan dimentions(length and width)
2, the dimention underneath the body (outside to outside) right above the rearend.

thanks!
B


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.