Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> what rear?
User Name
Password
lost password?   |   register now

Thread: what rear? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-16-2003 04:34 AM
woodz428 Ford spring perch width was standard from the nid fifties until they went coils on everything. You probably have a intregal carrier if it was a six (has 4 bolts on the wheel). An 8" while not as strong as a 9" will give you more than you have but not quite enough for a stout big-block. Any early Fairlane ('64-70), '67-70 'stang/Cougar will fit as will the 8" from an MII, Granada/Monarchs(and the disc braked Versailles. All those should get you tires that stay under the fenders, late '50's early '60's big Ford rears will bolt in also if there is a source in your area.

[ April 16, 2003: Message edited by: woodz428 ]</p>
04-15-2003 09:45 PM
rustyrazer so what rear will fit my car? I want one with some oomph and what car at the junkyard can i take it off of?
04-15-2003 08:40 PM
Deuce

There were NO 9 inch rears installed by FOMOCO into 69 Falcons I am told. To check your car........if you can put a socket on the bottom center section bolts.....it is a 8 incher.

This has been mentioned many times here in previous post. It is a old junk yard trick.



This is a 9 inch, 31 spline, Detroit Locker with 3.50 gears.

Some folks believe you can tell spline count by looking at the ends of the axle where the brake drums go. I have read this also on the Web. I have found it is not 100 percent accurate.



04-15-2003 08:14 PM
rustyrazer
what rear?

so i have a somewhat stock 69 falcon with a auto on the column shifter--so i am guessing its a c4 tranny? anyway two things--i want to get a rear at the junkyard to give my car some more oomph what car can i get them off of and what years--also i am interested in putting in a auto stick on the floor--is this hard to do--you know one of those sticks where the clutch is the lever (b&m) anyway the rear end question is the more important one--cause im going to the junkyard tomorrow and i need to know--so am i looking for a 8 inch ford or a 9 inch--i just need to know what will fit

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.