Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Frame front clip swap????
User Name
Password
lost password?   |   register now

Thread: Frame front clip swap???? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-14-2006 11:19 PM
lakota Hey Old Timer,

It's coming along. I've made a couple of changes in the past week, like bolting the cab directly to the frame instead of using angle brackets and making a homemade altenator bracket to mount the altenator lower and closer to the engine. In answer to your last question, if you're still thinking of using an S-10 frame. I don't think there'll be too much stress on the front end and bearings with 2" spacers. Off roaders use them all the time with good results. With 2" spacers on each side of the front wheels, it will bring your stance out to almost 60". Along with the 60" rear from a 4X4 S-10, you should be good to go. If you still need to fill out the fenderwell, go with a wider tire.
03-12-2006 04:27 PM
Don Meyer IN the Chevy trks 47-54 I've used Camaro & G body clips(78-88). The G body's clips are approx 3" narrower,thus are the same track as the original trk.

Thus, if your current track is aroung 58" you might consider the G body clip.Here are some more pictures http://71.65.63.136/web/photos/default.aspx
Don
03-12-2006 08:21 AM
shine i've clipped many early chevy trucks. the camaro will work fine. just a tad wide . all 70 up camaro's were front steer. the s10 works well also. i'm using one under a 46 ford sedan i'm building.
03-12-2006 07:28 AM
Old Timer Hey Lakota,
Those ideas have crossed my mind however my thinking is that one would be over taxing wheel brg., steering and suspension? What ya think?
Hows that Ford P/U coming?

Thanks
Old Timer
03-11-2006 11:47 PM
lakota There's always the "down and dirty" method. Use 2" spacers or 1" spacers and wider rims.
03-08-2006 07:08 AM
Old Timer Thanks Lakota,

I hear what your saying however from the stock front I have a 4,3/4 track width difference from the S/10 front frame clip and one issue that concerns me is that the wheel will set inside the fenderwel to far and look weird.
What ya think?

Again thanks for the come back
Old Timer
03-07-2006 10:32 PM
lakota Old Timer,
I had the same problem with my 52 Ford F-1 pick up when I swapped out the frame to an S-10 frame. The original Ford rearend width was 60 inches, the S-10 is only 55 1/2 inches. I've swapped my rearend to an S-10 4X4 rear because it's 4 inches wider (59 1/2 inches). Both the S-10 and the S-10 4X4 rears have the same spring perch measurements (40 1/2 inches), so it's a direct swap. For the front width I used a 1 inch spacer on each front wheel. That shouldn't cause too much stress on the spindles.
03-07-2006 09:40 AM
Old Timer Thanks Jerry K.
I've been scratching my head and pacing the floor as what to do and with that I got wondering if the market had any products to update,such as power steering,suspension for the late 40's and early 50's Chevy?

Again Thanks
Old Timer
03-07-2006 08:55 AM
JerryK I have a friend that bought a 50 Ford car (should be near the same as your Chevy) with an S10 front clip in it. He seems satisfied with how it drives but unhappy with the looks. It is too narrow for those cars in my opinion. I have clipped several cars and a pickup with mid 70's Camero type clips that have worked great and are a bargain considering the end result. One thing you need to consider when measuring is the desired ride height. Some cars have plenty of tire to fender clearance at the stock ride height but it may change a lot when you lower the front end. Good luck!
03-07-2006 07:35 AM
Old Timer Gents,
Thanks for the come backs you've been very helpful.

If anyone else has some input I would be very appreciative.

Again thanks
Old Timer (aka) Dick
03-06-2006 06:05 PM
astroracer
Quote:
Originally Posted by Old Timer
My reason in choosing the S/10 is the fact that I have one a freebee. But Ya got me thinkin. just keep the ideas a comin please.

Thanks
I hear ya... Free is good, BUT... if it doesn't work, you will be spending more time and money to "fix" it then you would be to get something that will work right upfront and save yourself a lot of hassle and heartache... Do a lot of measuring before you start cutting.
Mark
03-06-2006 05:59 PM
Old Timer My reason in choosing the S/10 is the fact that I have one a freebee. But Ya got me thinkin. just keep the ideas a comin please.

Thanks
03-06-2006 05:48 PM
astroracer Do some measuring of the steering box on the S10 frame. The s10's are front steer and the box may get in the way of the fenders when you put them back on. The F car subs are rear steer and the box isn't a factor for fender clearance. You may want to look for a 2nd gen Camaro/Firebird/Nova front sub to solve ALL of your problems. Another option may be one of the full framed mid-size cars. 4th gen Monte Carlos, Grand Prix, Cutlass and Buick Regals have a fairly wide stance and may work for you also.
The rear track width can be adjusted with rim offset but the front is another thing. You don't want to push the wheels outboard to far because of bearing wear and bump steer that is induced by the increased lever arm of the offset wheel. Keep the track width as close to stock as possible in front (a little wider won't hurt anything)
03-06-2006 05:16 PM
Old Timer I'm not so sure the pannel would be the same as a Sedan/delivery as the S/D used the pass. car chassis and a pannle use the 1/2 or 3/4 ton chassis maybe.
03-06-2006 05:03 PM
gl perkins
glperkins

i have a 48 chevy panel i am using a camrao off a 77MODEL AND IT WORKS GREAT I 'D. say your is the same
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.