Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Adjusting valves
User Name
Password
lost password?   |   register now

Thread: Adjusting valves Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-31-2006 11:24 AM
Classic Ed
Great!

Thanks alot that was a big help!
03-31-2006 05:42 AM
BBCMudbogger If the cam is hot with high lift and stiff springs you should definately break it in with lighter springs.....BBCs will eat the cam up if the spring pressures are high
03-30-2006 05:22 PM
Decho Some people can be difficult, but I'm sure Edelbrock is just trying to CYA
I've attached the Edelbrock cam install instructions. It's in 3 languages, just in case you're in a foreign country and need to adjust your valves

Good luck!

Decho
03-30-2006 04:34 PM
Classic Ed
Edelbrock

I looked on their website for the installation guide for adj cams but didn't see it. I emailed them & a guy asked alot of questions & then wanted the model # of cam. I gave it to him but it was a Howards cam. He wrote back & sd thats something you have to ask Howards Cam.
03-27-2006 06:05 PM
Classic Ed
Adjusting valves

I will definately ck it out, thanks alot.
03-27-2006 05:45 PM
Decho If you look on the Edelbrock website, they have an installation guide which tells how to adjust valves properly. I have installed cams before using their method as well as the running method and I preferr the "zero lash and half turn" method best.
03-27-2006 05:11 PM
Classic Ed
Adjusting valves

Thanks, is there any other way to adjust valves without running engine, very messy?
03-27-2006 05:00 PM
poncho62 Bring each cylinder to TDC...adjust to zero lash......give extra 1/2 turn. That should set them so you can start it.

When starting it first time, keep the RPMs up about 2000 for at least 20 min to break in cam.

To adjust with it running, back off each rocker until it ticks. Tighten until it goes away, then give it another 1/2 turn.
03-27-2006 04:50 PM
Classic Ed
Adjusting valves

I just rebuilt a 396 big block chevy, has new cam & lifters. Engine is completely back together, my question is, whats the best way to adjust the valves for the 1st time? Engine is out of the car. Hydrolic cam.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.