Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Taurus SHO clutch issue... I know, big surprise...
User Name
Password
lost password?   |   register now

Thread: Taurus SHO clutch issue... I know, big surprise... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-04-2006 08:33 AM
ViperMonster800 Quadrant was fine. I'm guessing its the throwout bearing but it would be better to upgrade to the 9 3/4" clutch. Thanks.
04-01-2006 11:37 PM
DHMag coming from a SHO owner, im confident in answering this. simply enough, you need a new clutch set. the fingertips on the pressure plate have prolly snapped and worn the face of the TOB and now the fingers are hanging onto the TOB.

hopefully the original owner took the SHO in for the clutch uograde. 89 and 90 came with a 9.25" clutch, the TSB upgraded it to a 9.75" clutch. this can easily be checked without removing the transmission, but starter removal is required. a new 9.75" clutch set can be bought at for favorite auto parts store for around the price of $270. it comes with a pressure plate, clutch disc, throwout bearing, and alignment tool. if it is the smaller clutch, youll have problems finding them, though it is cheaper.

with the new clutch set, youll more than likely need to remove the quill sleeve on the trans inout shaft quill. while some have had issues removing it, i have not. just pull back on the tangs, and twist and pull,

as for the clutch adjustment, the quadrant is notrious for not holding its position when adjusted. i had to get under the dash and engage mine using a screwdriver.

though the site is down right now, check shoforum.com. im there with the same user name as well.


any other questions, feel free to PM me.

Dale
04-01-2006 10:59 PM
BstMech When you do get it in gear, how far off the floor do you have to let the pedal come before the clutch engages (car wants to move)?

Does this distance ever change say with the engine/tranny hot or cold?

Does the amount of freeplay travel in the pedal ever change?

Does this noise occur when lightly pressing on the pedal, or when the pedal is at full travel (clutch disengaged), or both?

It sounds like the clutch isn't fully disengaging which is why it's hard to get into gear. Most noticeable in reverse because of the lack of synchronizers in reverse. This can be caused by most anything in the clutch assembly. If I remember right that year of Fords still had a manual adjustment in the clutch pedal. You had to pull up on the clutch pedal periodically and the pedal assembly would self adjust the freeplay. Make sure if equipped, that this mechanism isn't causing the problem by not allowing enough travel to fully disengage the clutch. Should be no more than an inch or so of freeplay in the pedal.

It sounds like clutch time.
04-01-2006 10:14 PM
ViperMonster800
Taurus SHO clutch issue... I know, big surprise...

My brother's '89 Taurus SHO was bought for $265. It has 106,xxx miles on it and runs great. However, the clutch is a quirky little son of a gun. When you press the clutch down all the way, it makes a noise that matches the engine speed. Not neccessarily a grinding noise, more of a slight paper-like noise.

We thought it might be the clutch cable so we replaced that for a fairly cheap $30. Grabs a little better but the next day, it just doesn't grab any gear at all. I don't know how to explain it... but I'll try. I push in the clutch, put it in 1st gear, and hear massive paper-like noise. I attempt to put it in reverse and it just grinds so I don't put it in at all.

We know its not the clutch cable but it could have been needing a change anyways. So if its not a clutch cable, is it the throw-out bearing? It so definitely seems like it. My brother and my father both think its the clutch fork or my dad thinks its just a clutch job thats in order. He had a '87 Taurus MT5 - 4cylinder w/ a 5 speed - and he had that done with a clutch job for $800 and my mom got mad at him for doing that without talking to her.

Whats your opinion?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.