Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> question about mp brakes setup
User Name
Password
lost password?   |   register now

Thread: question about mp brakes setup Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-17-2006 01:18 PM
38 old coupe hello i called brake tech solutions the guy says he is the one who makes these setup for other company's and he is going to make me a pedal for 50 dollars im going to try a 16 inch pedal and from center of pivot point to center of hole for booster is going to be 2 and 3/4 inches witch gives me a 5.82 to 1 ratio he said it is going to take 2 weeks or so and i was told when i get it all filed with fluid i can adjust the pedal hight. i could only go 3 inches longer because the way the fire wall comes down flat then so far down had a slope to it before it hits the floor . thanks kelly
04-16-2006 09:50 PM
powerrodsmike If you make it longer on the pivot side of the pedal as well as the bottom you can keep the proportions the same . here's an example: if your current pedal is 6:1 and the center to center dimensions are 2" from pivot to pushrod, and 12" from pushrod to pedal pad, then you could add the 6" from the pushrod to the pedal pad, making it 18" . you would then add 1" to the length between pushrod and pivot making it 3". then it is 18:3 or 6 :1. you would have to move the upper mount up 1" to keep the M/C in the same place. I would make a new pedal if I was going to go to all that trouble. hope this helps, mikey
04-16-2006 09:15 PM
38 old coupe ya but if i make the pedal longer it will have 9 to 1 ratio kelly
04-16-2006 07:05 PM
techinspector1 With power brakes, 4:1 is not a problem.
04-15-2006 08:55 PM
powerrodsmike Can you extend the pedal a proportionate amount on the top as you do the bottom and move the upper mount so you keep the ratio the same? Or maybe move the upper mount and use a pedal out of a '70's pickup. some of them are pretty long. Just a thought. I was going to use one of those universal hanging pedal things from MP in a 33 pickup but I ran into the same problem. Pedal was too high off the floor. I wound up making my own pedal and bracket. In any event you want to keep the ratio at 5 or 6 to 1 for power brakes.
hope this helps, mikey
04-15-2006 08:37 PM
38 old coupe
question about mp brakes setup

i bought a mp brakes set for my 38 olds coupe installed it today it was a universal 7 inch duel booster setup. i made the bracket sit flush with the bottom of my dash . now the prob is the bottom of the pedal sits 12 inches off the floor and i have it set to the back hold on the mount and it is 12 inches off the fire wall i haven't put fluid in but it says to set pedal so that 1 1/2 out from floor when bottoms out where it is set up at with this measurements im 1/4 inch from floor when bottoms out i was thanking of adding 6 inches to the pedal length but then i would have 9 to 1 ratio instead of the 6 to 1 ratio but the 12 inch off the fire wall wont work . any ideas next would to return it and get a Manuel set up from wilwood. but i would like to have the power setup. also the pedal length is 12 inches and they don't make there pedals longer and i cannot go under the floor i only have 5 inches to depress the pedal tell it hits the tranney bell housing . thanks kelly

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.