Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Almost finished fitting / shaping f/g trunk, starting the hood
User Name
Password
lost password?   |   register now

Thread: Almost finished fitting / shaping f/g trunk, starting the hood Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-05-2006 06:50 AM
readdirections i also went thru the same problems with my fiberglass trunk lid. i also found pockets under the gel coating. had to go all over with a scratch awl and pick out the pockets, some 1 1/2 " long and sand the cavities and fill with duraglass filler. found it to be the same with my side scoops. i am leary of painting , so i may leave in epoxy primer for a while.
05-05-2006 06:31 AM
baddbob It sounds like you're taking your time and perfecting the fit, the final product will be well worth all the hard work. I've never seen a fiberglass part that didn't need some amount of straightening or fitting. You're going to have one nice ride when she's all done! Bob
05-05-2006 03:58 AM
kenseth17 Glad to hear you are making some progress ripped. Just think how good you will become at fiberglassing and shaping after this. I hear you on the not planning on it taking the time it does. That is why if someone asks how long something will take to do, I won't give a firm answer. You never know what hurdles you will run into and have to overcome.
05-05-2006 12:53 AM
Ripped
Almost finished fitting / shaping f/g trunk, starting the hood

I have to say I did not think it was going to take 8 weeks of work (after work at night) to fit the fiberglass trunk and extensions, but finally there is a light at the end of the tunnel. Tonight I flipped the trunk upside down, and began to tune up the underside of the edges and lips where reshaping took place, I hope it does not take more than a few nights.

I am now preparing for the fiberglass hood and nose section /fascia. This is much better fitting than the trunk to begin with. I did not think it would take more than a few days. However after my pickiness with the trunk fitment, I think a few days is overly optimistic. I hope that my experince on the trunk will make me a little speedier at taking the right steps in getting the hood aligned, gapped, and shaped to the fender and fascia contours.

I guess if I figure on another 8 weeks, I won't be in a hurry

I am very pleased with how the trunk looks, I'll post some pics soon.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.