Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> What should I set my timing at?
User Name
Password
lost password?   |   register now

Thread: What should I set my timing at? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-11-2006 11:37 PM
docvette Doc here,

Early 80's 305, with CCC or CCCC Computer (or not), 8 Degrees static . Hook the advance unit back up , Manifold source for power, ported source for economy and smog..

Detonation sounds like marbles being shaken in a can..occurs usually under throttle load, and uphill pulls..Being that far advanced will probably make it run a bit hotter than normal.

After you set it for 8 degrees , take it on to the freeway, going up the ramp..Hammer it..If it pings / Rattles.. retard it. If it barks like a dog, advance it a bit..

Don't know what to tell ya about turning the engine over by hand with no valve action..but that doesn't sound right..maybe with a socket and breaker bar..Do a Vacuum Check .. 17 to 21 In Hg and STEADY, Bouncing Rapid Needle indicates burned/Leaky Valves, Guides, or seals..

Do a Compression, 125 to 150 PSI + / - 10% all the way around is good..much lower think rings/ rebuild.

Did you break in the cam properly ? 2000 RPM for 5 to 20 minutes?

Doc
05-11-2006 11:01 PM
97Z28 try dropping the timing to around 10 - 12*. and make sure you hook the vacuum advance back up. then test drive it and see if that helps.

were the spark plugs in the heads? if they were then you may have blowby issues. i'd do a compression test and leakdown test and see what you come up with. you will hear a certain amount of air rushing past. but it shouldnt be so easy to turn by hand.

hope this helped!

-Matt
05-11-2006 10:11 PM
Anton
What should I set my timing at?

I'm unsure what to set my ignition timing at on my 305 (early 80s), it has an edelbrock 1406 carb, 2101 performer intake and performer cam (summit but equilivant) and factory HEI dist,. I searched and cant find any information on factory timing specs.

I currently have it set at 14* BTDC base with the vacuum advance disconnected.. Cruising down the highway i can hear a ticking sound coming from the engine, is this pinging?

Looking for reccomendations for what to set it at for best fuel economy (factory specs im assuming?).

Also, should I be able to crank the engine over by hand with all the valves fully closed (pushrods removed)? I did this while changing my cam and could hear the air bleeding out.

thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.