Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> rebuilding a 54 front end?
User Name
Password
lost password?   |   register now

Thread: rebuilding a 54 front end? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-29-2002 07:54 AM
Phat Tucker Yes i cut the frame behind the cab about but in front of the e-brake holes. Pretty much any suspension you would want..air ride ..leaf springs..This one just got a complete vette suspension front and rear.

[ April 29, 2002: Message edited by: Phat ]</p>
04-28-2002 03:58 PM
tucker916 Phat, On those 3/4 ton frames, do you shorten them in the rear and put short beds on them? What kind of rear suspension do you usually use?
04-26-2002 08:33 AM
Conner thanks,phat.im going to look into this a whole lot more(stock or kit).when i get around to the sway bars,i'll make sure to do what you asked.thanks again.


Conner
04-26-2002 05:33 AM
Phat First off conner if your going to use a smallblock you have to move the steering box if you use the stock one.(it wont clear the ex manifolds no matter which ones you use)I also have not seen to many powersteering kits i could recomend. Most give you problems mounting the front shocks and or bumper and limit your turning raduis on right turns(tire hits the steering box) On sway bars..by all means put them on..but do a little test for me ..drive it with them on and than disconect the rear one..i have done the last 4 trucks like that and the guys like the rear ones not hooked up(but now you just have to remove it not cut up everything to install it)...I thought they drove better myself but i used to race oval track cars so my driving style is probaley a little screwy. In the end i think you will have done better by using a kit to do the front.The monos do ride ok...not a big improvemnet but good.(if i were to replace brokin springs i would do it,but they are pricy) but start adding up all the parts to do it. I have takin more than one truck apart that had all that stuff in it. I think you must decide what you want from your truck first. Are you just going to go to your local show ??Are you going to get on the highway and drive the thing to events 100's of miles away?? Get a budget together than add 33% to it .But spend the best money on the frontend,it will not be wasted.

[ April 26, 2002: Message edited by: Phat ]</p>
04-25-2002 06:06 PM
Conner im glad to hear the frame is good for hot rodding.i have to ask you since this is your profession.what do you think about the power steering conversion for the straight axle.would the front and rear sway bars and monoleafs be enough to handle the small block or should i add the conversion?thanks for the response.

Conner
04-25-2002 12:53 PM
Phat Hey Conner. I have built a few 54's and other assorted 47-55 1st. First my own personal truck is a 54 with a striaght axle and with some mods drives great. I can get in it and go 500-1000 miles in a day.(gettin to old to do that..but the truck could) Second all the rods i have built lately i have been using the 3/4 ton frame..its striaght and a good solid frame to start with. Third point(i do this for a living) I would not put the Fat stuff in anything..not even a go cart.I have had more problems with his stuff than you can know.Just finished cutting one all up the other day to get it so the guy could drive it.he uses the wrong rack,the anti dive is screwed up and i have seen with my own 2 eye 3 crossmembers that cracked and broke in the last 2-3 years.(the duluxe fluff and buff kits) If you do go stangII go with TPI-heidts or progressive. In what ever one you do you need to upgrade the brakes to 11inch and caliper to the old style 70's big calipers..not the little metrics. You also need to go full lower a-frames..the stock style strut rod frontend is just plain wrong.If you put a strut rod on a lower a-frame try to move the a-frame up and down in its travel 3-4 inches up and 2 inches down.Guess what it aint gonna happen,plus the caster is not stable under braking.They also break. I really have been using Bob at progressive more .740-862-4696. But the TPI unit is also a real good piece.
04-25-2002 06:59 AM
Conner thanks Jack,that should put me on the road to the rebuild.appreciate it

Conner
04-24-2002 07:18 PM
WoodsEdge Sorry about my answer, Conner, I misread you. If you want to go to disc, I'd call Master Power Brakes in Mooresville, N.C. 888-251-2353. I put disc on a 50 ford, bought only their brackets and they told me what roters, bearings, etc. to use, even gave me part numbers. Good co. to deal with. Jack
04-24-2002 07:20 AM
Conner thanks Jack,if i cant get this rebuild under way i just might have to do a clip or MII.the only thing holding me back from the rebuild id its a 3/4 ton truck with 8-lugs.im going to change the rear end.so im pretty sure the lugs won't look rightbeing 8 in front and5 or 6 in back.just need to know how to change the front lug pattern.someone on this board has to know.because im in the dark.thanks for the responce though.i appriciate you taking your time.

Conner
04-23-2002 08:43 PM
WoodsEdge The easiest way I've found is to go to a Mustang II front suspention. Don't know how stock you want to keep it. I'm building a 50 Chevy panel truck but its going to be a hot rod. I used a Fat Man crossmember and stock Mustang II a-arms and springs with 82 Caprice 11" roters. I'm also using the Caprice rearend with Posie's springs. I also went with a power rack and power brake master cyl. Brent at Fat Mans will be glad to answer any questions you have. This is a fairly simple swap if you can weld and fabricate. Hope this helps, Jack
04-19-2002 02:24 PM
Conner
rebuilding a 54 front end?

hello,my question is about rebuilding the front end of my truck,adding power brakes,power steering,disc brakes,etc....and dropping in a small block.its a 54 3/4 GMC,would this be pratical?and how could i change it from 8-lug to 5 or 6 lug.just getting more conviced to keep the I-beam.thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.