Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> TH 350 1-2 Manual shift Feel
User Name
Password
lost password?   |   register now

Thread: TH 350 1-2 Manual shift Feel Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-16-2006 09:20 PM
HarderTranz its not the stick shift one, 2 and 3 i think with the orange PR spring, checkball closest to the mod left in., removed tranz from vehicke today and found that kickdown cable was non existant, customer did not install it said that it was to hard to put the bolt in it. and i belive this is what caused his failure due to insuficent line rise, took everythin apart int and direct is burnt, air checks are good, all seals are good,



now another question.. red altos or blue plate specials?? bolth with koline steels. witch would benifit this trans more i wanna see opinions the more the better!!!!!
05-16-2006 09:07 PM
Crosley
Quote:
Originally Posted by HarderTranz
Im currently wotking on a 350 with about 600hp infront of it , i used a tranzgo shift kit, blocked the 1-2 accumulator with a piece of copper pipe, only one checkball is installed in the case, band is blocked from applying with washers under the servo, im using the large vaccume mod,

now. when im doing a manual shift from 1-2 at about 3/4 throttle aprox 5000 rpm the shift dosent feel positive enough the rpm's can raise 1000 rmp in the time it takes to make the shift. the shift dosent happen immeadeatly, i am using blue plate specials regular steels, im throwin kolines in it tomorow, i set my clutch pack cleaance to about .030 using an extra steel plate, should i have done this or left it with the big gap that it usualy has, none of the frictions are burnt and fluid is clean, mod is adjusted up.. and govenor is functoning correctly, withc i know is unrelated to a manual shift can anyone please give me some advice on this

Thanks

Cam

which TransGo kit?

Did you change the PR spring?

Which check ball remains in the case? what area is it located near?
05-16-2006 08:24 PM
HarderTranz Anyone????
05-15-2006 09:30 PM
HarderTranz
TH 350 1-2 Manual shift Feel... shift delay

Im currently wotking on a 350 with about 600hp infront of it , i used a tranzgo shift kit, blocked the 1-2 accumulator with a piece of copper pipe, only one checkball is installed in the case, band is blocked from applying with washers under the servo, im using the large vaccume mod,

now. when im doing a manual shift from 1-2 at about 3/4 throttle aprox 5000 rpm the shift dosent feel positive enough the rpm's can raise 1000 rmp in the time it takes to make the shift. the shift dosent happen immeadeatly, i am using blue plate specials regular steels, im throwin kolines in it tomorow, i set my clutch pack cleaance to about .030 using an extra steel plate, should i have done this or left it with the big gap that it usualy has, none of the frictions are burnt and fluid is clean, mod is adjusted up.. and govenor is functoning correctly, withc i know is unrelated to a manual shift can anyone please give me some advice on this

Thanks

Cam

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.