Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Rearend Measurements
User Name
Password
lost password?   |   register now

Thread: Rearend Measurements Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-27-2002 07:10 AM
Stinkin_V8 I'm guessing if you need a Currie rear end, you've got enough juice to need some fairly big rubber in there. I don't know what the rule of thumb is for clearance. I should have between 3/4-1" clearance on my inner fender wells with the additional spacers I mentioned. Maybe some of the other folks here could pipe up with their reccomendations.

I have no clearance problems on the outer fenders, but you'll want to watch the travel of the suspension. If your truck is real low, the rear axle may move enough to contact the inner fender above the wheel opening.

Sounds like you've got it figured out - get the wheels, put 'em in the wheel wells and measure.
08-26-2002 03:39 PM
Bruce H Stinkin_V8,

Thanks for the info. This really helps, and reinforces what I was kinda' thinking. If I am reading you correctly, I should be able to obtain my wheels and tires (keeping in mind the bulge) that will fit inside my fenders, then take my measurements from there. Spacing from the frame should be kept at about 1" to 1-1/2" with the same from the fender? Thanks for the link too, it is one I have not seen before.
08-26-2002 09:26 AM
Stinkin_V8 Sorry, I got a little click-happy. it's edited now.
08-26-2002 09:25 AM
Bruce H Stinkin_V8,

Got part of your message, but no link(?). Can you please re-post?
08-26-2002 09:19 AM
Stinkin_V8 Bruce,

Check out <a href="http://50chevy.freeservers.com/Suspension_Widths.html#Suspension" target="_blank">this link</a> for some common widths. Backspacing on your wheels is going to play a factor, but as long as you know what the backspacing will be you'll be fine. I've got a stock '89 S-10 4x4 rear end (58"?) under my '52 Suburban (same chassis as the pickups) and with 4" backspacing on P235 75R15, I only had about 3/8" clearance between the tire and inner fender well. Forgot to take tire bulge into account when I measured. A couple of 3/8" spacers can be had for cheap.

If you don't know what wheels you'll be using, you can narrow and widen the track width by specifying the backspacing on your wheels when you buy them.

[ August 26, 2002: Message edited by: Stinkin_V8 ]</p>
08-25-2002 08:33 PM
Bruce H
Rearend Measurements

I have a '53 Chevy p/u that I have purchased a TCI Mustang II IFS front and four bar rear airbag suspension for, and am planning on ordering a Currie 9" rearend. Currie's website explains what measurements need to be provided when ordering, but I need to know exactly how to arrive at these measurements. I suspect I need to have my wheels and tires on hand in order to get these measurements (?), and I don't want to order a rearend more than once! Any advice anyone can give me would be greatly appreciated. Thanks in advance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.