Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> bleed the brakes?
User Name
Password
lost password?   |   register now

Thread: bleed the brakes? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-04-2006 11:43 AM
rj57 Good advice offered here.

One important thing to remember:

When bleeding the brakes make sure to keep and eye on the brake fluid level in the master cylinder.

If it goes dry......... you now get to start all over again at the farthest point from the master cylinder.
07-04-2006 11:34 AM
fiddyfofoad
re:brake bleeding

the best way to bleed the brakes reequires 2 people. a pedal pusher and a bleeder. first off. make sure your brake shoe adjustment (shoe to drum clearance) is not way out, like matti says, there should be some drag when you spin the wheel. if not, then you're going to have to adjust your clearance with a brake adjusting tool on the adjusting star that it behind the oval rubber plug on your backing plate. by turning the star you will expand your shoes and bring them closer to the drum. when you're sure you have the right amount of drag on all four wheels you can start the bleeding process. first, open the lid of the reservoir and make sure it is full. the best way to visually see air leaving the system is to get a tall glass and fill it half way with brake fluid. next get a length of clear plastic tubing that will fit over the bleeder fitting and run the hose down into the glass. start with the wheel furthest from the master cyl and have your pedal pumper depress the pedal slowly to the floor 4 times and hold it to the floor while you crack open the bleeder fitting and watch all of the air bubbles rush into your glass of brake fluid. with the pedal still down on the floor, tighten up the bleeder valve. you do this until no more air comes out of the plastic tubing. periodically you will have to check the level of fluid in the master cylinder so it does not empty out during the bleeding process. next, you go to the 3rd furthest wheel from the master cyl. and do the same process till you get the same results, checking the fluid level as you go. then the 2nd furthest and finally the closest. typically it will be right rear, left rear, right front and left front in that order. if that doesn't solve your problem you probably need some new parts. good luck.
07-01-2006 03:25 PM
matt167 well, you need to crack open all the wheel cylinders bleeders first, then tighten them back up, then grab someone to be the pedal pusher, have them pump up the pedal, then hold it, open the bleeder, fluid and air should come out ( if air is the problem ) close the bleeder, do it until there is no air for each wheel cylinder, also adjust all the brakes using the star ajuster until there is a slight drag on the drum from the shoes contacting, this can also make a low pedal if they are ajusted too far in, the wheel cylinder pistions have to travle farther b4 they can build preassure.
07-01-2006 02:57 PM
UNWTRMY
bleed the brakes?

my 56 Dodge D300 brakes are squishy feeling when I push the pedal, I get almost no response until it is almost floored. everyone I have asked says to bleed the brakes, there is probobly air buildup in the lines. Makes sense to me, but heres the problem...

I dont know how to bleed the brakes! can someone help this newbie out?
its big drum brakes all around.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:21 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.