Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> A Arm bushing tool
User Name
Password
lost password?   |   register now

Thread: A Arm bushing tool Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-12-2006 07:05 AM
tm454
getter dont!!

use a hack saw to cut the old bushing in-two pieces..be careful NOT to cut into the A-Arm. Use the c-clamp tool to push out the old pieces. Use the tool to install the new bushing after cleaning up the hole inside of the A-arm to make it slide in easier.


Tazz
07-12-2006 05:47 AM
Bryan59EC I have - a few times - used an air hammer with a blunt tip - to vibrate them in.

A bit of lubricant and they will usually go right in.

I use the same method to get them out -- sometimes need the chisel though.

(actually did an arm yesterday)
07-12-2006 05:28 AM
Koolaid Uppers or lowers?

Lowers: cut out the originals, get some 2 x 2 x 1/4 angle iron - make some precise fit spacers to go in between the two gaps. Note that due to stuff moving around and being old you might have 4 different lengths cut for the 4 lowers, but odds are you're right and left will be the same. Just make sure you have it snug enough so that it won't fold and then press it in.

Uppers - You can press the first in normally, then drop in the second, make a long spacer so you won't fold the control arm and go to town pressing that one too. I have also had one or two urethane bushings that I could press out of the housing with persuasion so I could press the uppers in normally, then drop in the urethane and use the cross bar as a press of sorts to draw in the urethane.

Just my opinion - I've read about doing uppers while they are still on the car using heat and a hammer, but I'm a little leary of putting heat into the control arms.
06-20-2006 03:13 PM
sha_ba_do_bang you should be able to slide it over the press so your only pushing on on leg and the other side hangs below the press, i wouldn't buy the tool if you have a press

sockets make excellant bushing drivers!

Brendan
06-19-2006 05:40 PM
russlaferrera
A frame bushing instalation

Propaneburner, there is a special tool made by OTC and Kent More that looks like a C clamp, that has one end that is U shaped (so you can remove it from the bushing). I use a 2X2 angle iron, the length between the A frame with a deep socket on top of the bushing as the driver with a hyd. press Make sure the A frame is clean, so the bushing will slide in easier. Hope this helps! Russ
06-19-2006 03:37 PM
propaneburner
A Arm bushing tool

What is the proper tool to put new a-arm(control arm) bushings in place.?

This question is for a 79 camaro.

I have a press and stuf like that , but these arms are org. from heavy sheetmetal and i dont like to bent them while pressing.

Or just fill the gap with some wood/iron etc.

Thanks all.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.