Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Gm steering wheel nut
User Name
Password
lost password?   |   register now

Thread: Gm steering wheel nut Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-16-2003 11:22 AM
Busted Knuckles Thanks tm454, I looked at the threads with a magnifier and didn't see any damage. I'm guessing my column is from a first gen camaro/firebird, and I'm not real sure about the column the donor nut came from (I remember moving a bust T top out of the way, so it had to be mid seventies- early 70's), so it's prolly metric.
I'm glad you mentioned that the nut should go down easily (clears up that should I crank it down or not question).
Gonna stop by my favorite parts store this afternoon and just buy a couple different ones if they have them.
Thanks y'all. BTW, when I was in the Air Force, locknuts were called wife nuts....cause they don't go down easy... <img src="graemlins/mwink.gif" border="0" alt="[mwink]" />
01-16-2003 10:21 AM
tm454 Having made several steering wheel changes on 50's, 60's and earily 70's GM cars I can say the Nut goes on easily down to the wheel. A metric nut will or might JUST start and become tight/stuck. Don't crank it down if it stops just short of 1/2 thread as it may very well be metric. Any idea what year the column you have is from and the year the doner nut is from? I take it you don't have a thread chaser/tap and or die that large to gently run the column thread and doner nut? Say the nut and column are compatable but the nut won't start or run, If the column was laying around your garage you may have bumped the thread. Take a close look at the thread on the column as it may be squished and won't accept a nut. You can take a SMALL file to the thread if it is damaged and removed the smashed thread and allow the nut to run down. Also check with NAPA, they have books on just about everything and may be able to give you a heads up on what you need and even get you a new nut.

Todd
01-16-2003 09:21 AM
bullheimer NOT metric
01-16-2003 08:57 AM
Busted Knuckles Thanks Connman, It may be just the locking feature that I'm feeling when I start the nut onto it. Like you said, it turns a couple of threads and quits. It just feels kinda tight for a locknut.
But before I start crankin it down, I'm going back to the boneyard and grab some more. I'd forgotten that it could also be metric.
01-16-2003 08:30 AM
connman as far as I know same years up to about 80 same style{tilt/not}are same it should be locking locking nuts screw on a couple of threads befor it stops. turn 1/4 turn and inspect threads on nut and shaft try again turh it 1/2 and recheck junk yards full of cars go get couple of nuts metric and std
01-16-2003 06:04 AM
Busted Knuckles
Gm steering wheel nut

Anybody real familiar with GM columns?
I'm putting one in a F100, and I don't have the steering wheel nut. I took one off of another column at a boneyard. It appeared to be about the same year column. I tried the nut on my column but it either don't fit at all, or the threads are screwed up, or its a locking type nut.
Can anyone enlighten me before I screw up my column? Are they a standard NF thread or some off the wall GM specific thread size, (I can't find my thread gages)?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.