Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> '66 Mustang Power Steering
User Name
Password
lost password?   |   register now

Thread: '66 Mustang Power Steering Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-07-2006 03:12 PM
xntrik You might look into the integral saginaw unit used on the 71-73 Mustangs.
08-03-2006 10:18 PM
onebadmerc I bought a 1970 Mustang at a auction last January and it was missing half of the suspension. I needed to get the car to a rolling chassis status and had a 77 Granada parts car. To get the 70 Mustang up and moving I used the control valve, lower control arms, the front and rear springs off the Granada. Everything was a bolt in except for the front springs, which I had to cut down a coil. The control valve off the 77 Granada bolted in but the hoses wouldn't work, as stated above. This was done to a 70 Mustang but I would suspect that the 66 Mustang you have isn't much different.

Here is a link to the information on the suspension work I did on the 70 Mustang.
http://www.hotrodders.com/forum/1970...ion-75327.html
08-02-2006 10:04 PM
Ford GT ONEBADMERC - Sounds like you have done the Granada-to-'66 Mustang P/S conversion before. I have the Granada pump, so it sounds like the Granada hoses will work (I would use new hoses). I already have Granada outer tie rod ends because I have installed Granada spindles and disc brakes.

Have you actually performed this conversion?

Ford GT
08-02-2006 08:42 PM
onebadmerc The Granada control valve is different than the Mustang control valve. The Granada control valve will physically fit but the hoses are different. The Granada power ram is the same the Mustang besides the hose fittings. To make the Granada control valve and ram work on your Mustang, you will have to have custom made ps hoses. The hoses coming off the valve and ram will have to be the Granada style and the hoses going to the pump will have to be the Mustang style. You will also have to use a Mustang center link with Mustang inner tie rod ends, and you will have to use Granada ps outer tie rod ends to make this all work.
08-01-2006 04:01 PM
Bryan59EC I had a 65 once long ago when I lived in Santa Maria, CA--Took the PS right off-liked it better without the PS. I thought those cars were plenty light enough in the front--could almost turn the wheel with one hand with the car stopped.

My opinion only

Bryan
08-01-2006 01:06 AM
KULTULZ
Quote:
Originally Posted by Ford GT

Question: If I acquire a '66 Mustang center link for power steering, are the other Granada components usable (servo valve, operating cylinder, etc.)?
I think you are going to have to find that out on a trial basis...
07-31-2006 10:25 PM
Ford GT
'66 Mustang Power Steering

I have a '66 Mustang V8, auto with manual steering. I have a '68 steering box (16:1) and collapsible steering column to install. I installed front discs from a '76 Granada. I also bought the Granada power steering components, thinking that they might be adaptable to the Mustang, but the center link is obviously too long.

Question: If I acquire a '66 Mustang center link for power steering, are the other Granada components usable (servo valve, operating cylinder, etc.)?

Ford GT

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.