Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Which tranny will bolt up to mopar flat 6?
User Name
Password
lost password?   |   register now

Thread: Which tranny will bolt up to mopar flat 6? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-23-2006 01:12 AM
Paddyboyy A 55, 56 Plymouth 2 speed automatic will bolt up to your flathead. Some have a column shifter and some had pushbuttons.

Some info on this thread near the bottom:

http://merc583.addr.com/cgi-bin/webb...pl?read=147425

If you are on a budget and want to stay with the standard, I have one from a 49 Chrysler Royal...a 3 speed standard that I won't be using. It came out of a car with 75,000 miles that sat since 1969. It should be good, but I never drove it. You can have it for the shipping. I am in Calgary.
08-15-2006 11:56 AM
Nightfire Ok thanks a lot guys. Looks like the linkage has some worn out bushings. Im looking for the conversion shifter on ebay as I have not found any company that carries it. I've also found a company that makes an adapter for a TH350, should be a direct bolt on. I dont know if I'll go this route but its nice to know is a plausible option. Thanks guys!


Mike
08-14-2006 01:12 PM
redlightning Mike,
If it locks up on you while driving.Pull over and set the e-brake or block it up so it will not roll on you.Crawl under it to the trans and put both levers in the middle position(neutral).This should un bind it so you can get home.
I don,t know the about old mopar trucks ,if there is an adjustment on the arms.Do the same ,put both arms in the middle and put the shifter in neutral then adjust them until they are not binding.
This works on the old fords,also those cheap floor shifters work just fine also.That,s what I had in my 54 when I was in high school.I don,t know about an adapter.Carl


I just reread what jalopy45 wrote.He looks like he knows something about your mopar.What I put above was working on fords.I still think you adjust it in neutral if anyone disagrees please correct me.Carl
08-14-2006 11:03 AM
jalopy45 There are shifters made for your tranny, and they have to be for the mopar. You only have 1 shift arm on the side and one on top so other shifters won't work. I think that Speedomotive made the one that I used, you might find on EBay, try an inquiry at Inliners International http://www.inliners.org/ to see about tranny swaps
08-13-2006 12:44 PM
Nightfire
Which tranny will bolt up to mopar flat 6?

Hey gang,
2 questions here. My tranny and linkage are giving me a hard time lately. I think it might be just my linkage, but Im having trouble getting into gears and sometimes it gets stuck. So here are my 2 quesions

1) Where could I get a floor shirt conversion from the 3-on-tree that I have now? If Im replacing the linkage I might as well place the shifter where I'd rather have it. Do I need to get a mopar floor shift conversion or will the GM ones do?
2) What automatic tranny would bolt up to my flat 6 without too many modifications? I have a TH350 that was destined for my 267 SBC but I could always offer it up for my truck. Will it bolt up? What changes (other than new tranny mount and shifter) would have to be made to switch to an automatic transmission?

Keep in mind, I'm on a tight budget.


Thanks,
Mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.