Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Frame looks crooked
User Name
Password
lost password?   |   register now

Thread: Frame looks crooked Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-16-2006 11:24 AM
blacklotus I will try some of all that, of course this morning I went out there to do some wiring and I put a level on it just for giggles and it shows level in front back and middle.

I will keep an eye on it from time to time

Thanks for your help
08-16-2006 09:04 AM
powerrodsmike Henry is right, swap leafs.
It is really hard to tell if a frame is tweaked when there is a bunch of weight on it.
If I am looking to see if a frame is tweaked I put the front of the frame on 2 jackstands, and the rear on 1 in the exact center. That way the weight of the frame is not influencing the way it settles on the jackstands. Then put a level on it. I usually don't worry too much about anything less than 1/2" out on a truck frame when it is bare. Those f100 frames twist and rack a bunch when you are driving anyway.

If you want to see if it is diamond shaped, do the plumb bob thing as suggested ,or just measure from corner to corner.
I have yet to see one that is within 1/4"

Make it so it sits level when the suspension is loaded, and drive it.

If it is way out then it's the frame shop.
Later, mikey
08-16-2006 08:19 AM
Henry Highrise It could be a little fatigue in the rear leaf spring on the drivers side. Swap your rear leaf springs from side to side and see what happens.
08-16-2006 07:56 AM
jalopy45 It could be your suspension, You might want to find a level area like your garage floor and put jack stands raised equally under the 4 corners and see if they all settle evenly. You might also take a plumb bob and make a spot on the floor at each corner then take a measurement from corner to corner (in an X) to see if the frame is out of square. If you have any discrepancy the best thing is to let a good quality frame shop push and pull it back to straight. If it's your suspension start shimming and replacing. Or it could level out when you are driving depending how heavy you are.
08-16-2006 07:03 AM
blacklotus
Frame looks crooked

Okay last night I was standing in my shop looking at my truck and it looked odd so I put a level on the front of the frame and showed level then I put a level in the back and it showed not level. I then took a tape measure and measured off the floor to the bottom of the frame in the back and it was 1/4" short on the passenger side. It has all new bushings in the suspension and the cab (stripped) is all that is on it right now with the engine and trans etc.

Does this mean that the frame is racked? I thought I might lift it up on the low side with a hoist and see if it would settle down over time and get some of it out. Comments please.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.