Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> sbc block fill
User Name
lost password?   |   register now

Thread: sbc block fill Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-15-2006 05:15 AM Have "short filled" a few and never had a cooling issue. Last one was a 406 sbc in my S-truck. Salvaged a good 400 block that had a crack in lifter valley.
09-14-2006 10:49 PM
stymie I did it on a 2 bolt that I went to 4 bolt billet caps on. Figured it would be a good Idea being Its got around 500 hp and I run it hard at the track every once in awhile. I only did it after talking to several people. The consensus was it wouldnt effect the cooling at all, that 90 percent of your heat and cooling is in your heads. Well being in Tucson Az were it gets up to 110 on a regular basis I havent had any cooling problems whatsoever. But keep in mind I have alluminum heads and radiator and a huge electric fan.
09-14-2006 09:00 PM
dirtracerx It would actually be going in a circle track engine. Short races usually with lots of slow caution laps. I don't have a fan either. I have an electric fan that I switch on during cautions. Engine runs on methanol. Has a 195 thermostat. It never gets up to temperature until I run the feature event with more laps. Wanted to strengthen the bores and get better/more even cooling/heating. Thought that this might do the trick. Plan on putting it in a 4 bolt main 383 stroker for next season. Have a .020 over 010 block that I plan on using.
09-14-2006 08:54 PM
327NUT What would your reason be for using it on a streeter, I,m just curious.
09-14-2006 04:55 PM
nitro_baller4692 hard block is lighter ten cement,i have done this on a cracked 5.0 block but i would say it was not quite half long as your not sitting in dead stoped traffic for an hour you will be ok.
what is your set up before i say that?
it helps stenghten the block but i did it for other reasons,other then that it was on truck pullin engines big block chevy and they were completly filled heads and all.they made about 2200-2500hp.
i would not do it just for a street rod
09-14-2006 04:43 PM
sbc block fill

Has anyone tried a 1/2 block fill for street rod? Any cooling issues? How much weight does it add? Pros and cons?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 12:59 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.