Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> saginaw 4 spd embarrassement
User Name
Password
lost password?   |   register now

Thread: saginaw 4 spd embarrassement Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-03-2006 07:01 PM
paulo 1 OK guys.Thanks for all the suggestions.We are considering a new Hurst shifter assembly even though I understand there is a design flaw inside the cover,allowing it to happen.I imagine there was a TSB back
then,though.It should have put people into really embarrassing situations.If the new shifter does not solve it,I will extend the reverse curvy-slotted piece inside the cover.That will do it once and for all.
10-02-2006 10:55 PM
jimfulco Same here.

It helps to pull straight back on the shifter, maybe even with a little leftward pressure, when shifting out of reverse. This ensures that reverse is fully disengaged before the shifter moves into the 1-2 position.
10-02-2006 01:36 PM
johnsongrass1 Ummmm, I've done that.

Don't feel too bad.
10-01-2006 03:41 PM
OneMoreTime Check for worn shifter mechanism..some times those pins get worn and allow that to happen..The remedy seems to be replace the shfter pins and rebush the shifter so it is tight with no slop..

Sorry bout your difficulty..

Sam
10-01-2006 03:11 PM
matt167 normally rocking a car back and forth gets it unstuck
10-01-2006 02:17 PM
paulo 1
saginaw 4 spd embarrassement

Well,it happened to me.Our fully restored '74 Camaro is being test driven to debug the usual stuff.This saturday I was going up a narrow street on the out skirts of Rio de Janeiro when I decided to turn around and return.Back and forth a few times and suddenly when I began to let go the clutch pedal the car did not move but the RPM went down! Guess what? Tranny engaged in 2 gears at once! Unreal! The worse,we were fully blocking the street on a steep hill,output shaft stuck!Car would not move even when clutched...
Ran 2 miles to the shop,grabbed small floor jack and tools,ran back to the scene,raise,struggle,curse and with the help of all mighty God,I got it unstuck.
Upon inspection of the inner side cover shifter mechanism,I realized that it can actually be engaged into first before reverse is fully desengaged!
The stock shifter had been adjusted with the centering pin and care.You guys know of any remedy?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.