Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Garage Door Alignment
User Name
Password
lost password?   |   register now

Thread: Garage Door Alignment Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-02-2007 09:04 PM
jetnow1
Garage Door

go to a good garage door installer- they sell metal chanells that go on the
bottom of garage doors which should be able to cover the gap if none of
the other suggestions work.
10-18-2006 02:45 PM
daveh Thanks for all the useful suggestions guys. I will begin with those and report back later. Thanks

Dave
10-18-2006 02:43 PM
russlaferrera
garage door alignment

All the suggestions posted are useful. You need a starting point, Is the door panel level? Check the floor. Is it level? This IMO will start you in a logical diagnosis on what is wrong.

Should the door not be level. Why? Spring tension, rail alignment, binding, or something else not mentioned.

Should the floor not be level.. They make a floor leveler mixture for concrete, can you cut a tapered shim, cut the door panel (if it is wood) , add a aluminum channel under the door.

Hope I gave you some useful ideas ...russ
10-18-2006 01:02 PM
1ownerT Bryan is right, the floor could be out of level. One side may drag on the frame preventing it from seating properly. If it uses seperate springs mounted at the horizontal rail, one side could be a heavier duty spring. If the tracks are not plumb it could cause problems also.
10-18-2006 01:00 PM
66Caprice On my Craftsman 1/2 hp, it looks like the rails can be remounted or maybe even adjusted a little. Looks like it might be a two person job too.
10-18-2006 12:31 PM
Bryan59EC All you can do is check the door panels for being level

It is possible that your drive is not level.

This is the situation I have at my house----but not a full inch.

Bryan
10-18-2006 11:01 AM
daveh
Garage Door Alignment

Hi guys,

I have a two car garage and it isn't square when shut. One side stick's up about 1 inch when shut. I put some insulation inside the rubber seal at the bottom but that is only temporary. I would like to fix it the right way. I have a 3/4 hp craftsman automatic opener.

How do I adjust the door so it opens and shuts square. Thanks

Dave

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.