Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Unisteer installation on 32 Ford
User Name
Password
lost password?   |   register now

Thread: Unisteer installation on 32 Ford Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-02-2012 07:54 AM
Deuce I answered your PM ...

Sorry for the delay BUT I was out of town for a week. The wife and I went to The Rodders Journal event in Baltimore MD. For a first show ... it was KILLER. Great location, well organized and LOTS of 32 Fords.

My 3W @ Baltimore



There was a very high percentage of 32 Fords there

09-30-2012 08:06 PM
32deuce51
Unisteer

Hi Deuce, I'm the newbie!!! Thanks for the welcome. I'm doing over my 32 5w. I see the pics of the Unisteer setup on yours. You say you have a vega box in your other 32. I'm considering going that route. Putting in a 351 windsor and it's pretty tight and busy with the vega box with oil filter, fuel pump, and rad hose all in that area. Looks like I'd have more room with Unisteer. Which do you like better? Thanks, Lou By the way beautiful cars!!
10-24-2006 10:50 AM
pasadenahotrod
Parallel to the tierod not parallel to the ground.

The bracket should place the steering unit with the tie rod parallel to the tie rod but not necessarily in the same plane as the tie rod.
10-23-2006 10:58 PM
home brew And Deuce is one of the most friendly and informative members on the site. Do you have a close up of how the unit is attached to the frame?
10-23-2006 10:17 PM
Deuce
Quote:
Originally Posted by OU812
Deuce, thanks for the reply and pictures.
You are most WELCOME ...

Hotrodders.com is one of the most friendly and informative places on the web ...

Deuce ...
10-23-2006 07:49 PM
OU812 Deuce, thanks for the reply and pictures.
10-23-2006 06:48 AM
Deuce
Quote:
Originally Posted by heyjude076
Hi Deuce

Something I did not pick up on when I first saw these pics - no panhard bar? Is that because of Unisteer, 4 bar link or a combination of both?
I have a panhard bar ... it is just not installed in the photo ...

LOOK on the left side of the chassis ... just below the frame rail ... at the front crossmember and you can see the bracket hanging down a little. I used a TCI panhard bar setup. In fact ... all the front suspension came from TCI. I used the original 32 Ford frame rails from under my 32 3W ... ( complete with the matching numbers to the title ) but then added the TCI " phase III " show setup.
10-23-2006 04:44 AM
heyjude076 Hi Duece

Thanks for the reply to my earlier question. Guess I am also going to go this route. Something I did not pick up on when I first saw these pics - no panhard bar? Is that because of Unisteer, 4 bar link or a combination of both?
10-22-2006 02:50 PM
Deuce WELCOME to Hotrodders.com

As a Moderator here and a fellow 32 Ford owner, I want to be the first to WELCOME you here ...





Above are the photos of the UniSteer installed on my 1932 Ford 3W coupe. Click on the link below to see more construction photos of the 3W project ...

http://www.hotrodders.com/forum/jour...ge=1&reverse=1

Again WELCOME ...

Deuce ... Moderator
10-22-2006 11:10 AM
OU812
Unisteer installation on 32 Ford

I have a 32 ford 3 window that I am installing a Marval Unisteer into. Does anyone have pictures of resent installs they have done. Is the Unisteer to be mounted parallel with the tie rod? If so, then the unit hang very low. If you mount in the location of the vega box, then the unit is at angle. Anyone have any pictures or better instructions than provided by the manufacturer. Thanks for any help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.