Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Loosing antifreeze.
User Name
Password
lost password?   |   register now

Thread: Loosing antifreeze. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-27-2006 05:24 PM
docvette Doc here,

Check your oil, Is it Milky or Green?

Pull the plugs...Crank it over, does it "Spit" water out the plug holes?

Does the Starter spin fast when trying to start, a few revolutions, and then kinda lock?

All signs of a blown gasket or damaged casting material. Do a compression test..are a few low next to each other? Bad gasket..

ODD, though, That is is , as you say, not heating up and still using that much coolant.

Doc
10-27-2006 04:17 PM
matt167 yes, those 2.2 & 2.5 mopar's are notoriouse for cracking heads and warping. at my autoshop class, we pulled a motor that was tired but running 2.2 out of a minivan that was junk, donated for parts. being the blocks are easy to find, but the heads are not in, in good shape anyway. we pulled and cleaned the head, and checked it for str8ness ( machined flat bar and feeler gauges and cracks even b4 we considered keeping it, it was fine so we put it in the store room
10-27-2006 01:02 PM
rj57 If you have an issue with the head being warped and letting coolant into the exhaust, fill the cooling system full again and watch for bubbles in the overflow tank. Lots of bubbles means exhaust is getting into the cooling system.

We were told the 2.5 in my girlfriend's '94 Sundance had a cracked head by the dealer. After pulling the head off it looked more like a blown head gasket.

But I did replace the head and head gasket.

Also WHICH head gasket you use makes a huge difference. Go with the Mopar version you have to buy at a dealer. Even the Felpro's aren't worth using on the Mopar 2.2, and 2.5 engines.
10-27-2006 10:48 AM
johnsongrass1 You shoulda had that head rebiult or replaced. Those heads are notorious for cracking. Most times you won't see the crack without a MAG but grows alot with heat. Pull the No one plug and look for it being steamed cleaned from the water entering the system.

You can drive it with the Rad cap loose and see if it still loses the same amount. Reducing the pressure inside the system will often slow the leak.

Replace the cap too. They do go bad and push coolant out the gasket.
10-27-2006 07:55 AM
ggarvey
Loosing antifreeze.

Hi Guys,
Thanks for such a quick response. I didn't have the head checked for cracks, but it did look good. While removing the head gasket, I noticed that #1 cyl was clean from antifreeze and the others weren't. All plugs look like they're firing correctly.
I have never noticed any white smoke from the tail pipe. This enging has never been heated up and doesn't use oil.
Thanks again for your help. George
10-27-2006 07:09 AM
tnoftsger Read the sparkplugs, if one plugs color is drastically different than the others, you are probably leaking it into that cylinder and burning it.

This could be a crack in the block or head. Or a leak due to warped head or block.
10-27-2006 06:32 AM
poncho62 If it's not leaking it, it has to be getting into a cylinder, which causes white smoke....or, into the oil, which makes it all milky, There is nowhere else for it to go. Can you smell coolant while driving?
10-27-2006 06:30 AM
nitro_baller4692 was the head checked for straightness and cracks?
10-27-2006 06:13 AM
ggarvey
Loosing antifreeze.

Hey guys,

Hope someone can offer a suggestion about why I'm loosing antifreeze in our 89 Chrysler LeBaron, 2.5.
With 150.000 miles, it has started to loose antifreeze and I can't see where it's going. I have replaced the radiator, head gasket and thermostat. When the engine cools down, I need to add a couple quarts of antifreeze to top off.
Any help would be greately appreciated.
Thanks, George

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.