|09-05-2014 08:47 PM|
Some people were questioning the aluminum reflecting part being on the top of the p&s product. Here in the south where it gets very hot in the summer we have been using a radiant heat barring. It is a type "insulation" that reflects up to 95% from a heat source. Lots of brands, Big on home-green radio stations.
Radiant Barrier & Bubble Foil Insulation | Innovative Insulation Inc.
Lowes and HD should carry something like this.
My thoughts on this would be put this down first using what ever glue product seems to best way to you. Then use whatever you would be next, P&S, DM, KEEP cool, etc.It Should work any where. Used on Motor homes. Then go next with which of these products that you believe is the best product you think is best. Also how many of the those other insulating- nose blocking product you like.
Note I am not trying to change any ones mind on what they want to use.
DanTwoLakes makes some good points as some others others do.. I happen to agree that most of these companies make two products, one for sound and another one for heat. LS does and so does DM. I am not going back to check all the links on everything talked about. In reading through several threads on here and at least to on the HAMB. No one discussed the radiant barrier products. Rave reviews on home sites. Makes sense to me.
I do know some one who has used it is his house, big difference. He can even get in his Attic.You can walk up there in the dead zone in summer in South Texas.
I am going to do this in winter on my house.... My attic is a death zone now.
Just my two cents... HTH
|07-11-2014 07:14 AM|
I use a high solids latex paint, the cheapest of which turns out to be white ceiling paint, adding one quart of the ceramic microspheres to one gallon of paint. To spray it, I use a rented airless sprayer from Home Depot with the filters removed (there's one in the gun itself that people forget about) and a .025 tip. Of course, the spheres can be added to any paint and can also be brushed or rolled on.
I've also used process this to paint the interior walls and ceiling of my shop, my attic at home and the exterior of my business. It definitely is worth the effort.
|07-10-2014 12:11 PM|
This thread brought me to your great forum here. I am very excited as this seems to be EXACTLY what I was looking for! Not only that, but I clicked on ONE other thread which was highlighted at the bottom of one page and it solved another problem that I've been wrestling with for a while. I'm a Jeep guy, not a hot rodder (someday!), but I've exhausted the off road forums for a few dilemmas I've got... I can't wait to see how many other problems I can solve searching around here!
|05-04-2014 06:55 PM|
|05-03-2014 04:53 PM|
|Mrrman||Watching this thread...the lizard product is way overpriced so I always avoided it.|
|10-13-2013 08:54 AM|
|DADSSUB||What about bed liner? Would it help with sound deadening?|
|10-13-2013 08:51 AM|
|DADSSUB||Is the Lizard Skin mixture for sound reduction or temperature reduction?|
|10-12-2013 09:51 PM|
Following up on my post, I did my deck lid on my Chrysler today.
I mixed the micro-balloons I got from Wicks with a quart of Rustoleam latex paint. The mixture was thick, but still pourable. I removed the deck lid and striped out the lock etc. and taped all the openings except one access hole near the latch and the two holes where the hinges go in.
I poured the mixture in the three holes, and after sealing them with more tape, I then left it standing on each of its sides for a few minutes. As it dried, I left it in each position a little longer, spending most of its time laying face down.
When I was done, I removed the tape and propped it up on saw horses face up and let it drip for a while. To my surprise, not a lot of paint dripped out.
Got it cleaned up and put it back on the car later. First thing I noticed was the trunk closed with a much less "tinny" sound. When you knock on the sheet metal, it almost sounds like knocking on fibreglass, rather than the steel panel.
So.... I'd say it worked. If I were to do it again, I would mix up more than a quart of paint, but that's the only thing I would do different.
|10-03-2013 06:50 PM|
The top ten reasons are: COST.
Those insulating glass microspheres mentioned can be added to any paint.
|10-03-2013 04:15 PM|
Not that old of thread so I'm hoping people area still paying attention to it.
Was interested in finding out what the results were if you used some other paint instead of house latex. Our fab shop has a really nice primer they put on industrial duct work that I am planning on using inside my body.
I'm also a little confused why you would put the home made lizard skin over Dynamat? Don't they both do the same thing?
|09-15-2013 01:42 PM|
|09-15-2013 11:37 AM|
do one test panel first using outdoor latex. or alkyd enamel better .at menards for 24 bucks a gallon. keep us posted on test
|09-15-2013 09:27 AM|
|DanTwoLakes||I'm sure nobody has, but give it a try. What do you have to lose? At worst it doesn't work, but if it quiets the car down even a little, it will be worth it.|
|09-15-2013 08:55 AM|
This is a great thread that actually brought me here to lurk several years ago. Time for me to ask a question....
Has anyone ever poured the home brew Lizard skin into a panel opening and then rotated/turned/spun the panel to cover the inside?
I have a 70 Chrysler 300 vert that I want to quiet down. This car has the most highway noise of any of the big Mopars I've owned over the years. A lot of it seems to come out of the trunk area. The quarters were replaced sometime in the car's early lifetime and the usual heavy factory applied undercoating on the inside of the quarters is missing. I'll apply the Lizard Skin there and on the trunk floor.
I think I'd like to coat the inside of the deck lid too... but there is only some openings around the latch and hinges. I'm thinking I can take the deck lid off and pour some of the paint mix in the holes and twist and turn the lid until it's covered inside.
Has anyone done this??
|09-11-2013 09:05 PM|
I had some extra Dyna mat left over so I put some on my fuel cell corners since is is only about 6 in from my exaust,,not that I thought it would catch fire ,,but to help prevent vapor lock
don't know how it will stand up to the weather ,
|This thread has more than 15 replies. Click here to review the whole thread.|