Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> alternative to Lizard Skin
User Name
Password
lost password?   |   register now

Thread: alternative to Lizard Skin Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-11-2014 06:14 AM
hduff
Quote:
Originally Posted by JeepFreak21 View Post

Many thanks to Vince and all those who contributed here!
Billy
The first post is from 12-01-2006 and it's been active ever since.

I use a high solids latex paint, the cheapest of which turns out to be white ceiling paint, adding one quart of the ceramic microspheres to one gallon of paint. To spray it, I use a rented airless sprayer from Home Depot with the filters removed (there's one in the gun itself that people forget about) and a .025 tip. Of course, the spheres can be added to any paint and can also be brushed or rolled on.

I've also used process this to paint the interior walls and ceiling of my shop, my attic at home and the exterior of my business. It definitely is worth the effort.
07-10-2014 11:11 AM
JeepFreak21 This thread brought me to your great forum here. I am very excited as this seems to be EXACTLY what I was looking for! Not only that, but I clicked on ONE other thread which was highlighted at the bottom of one page and it solved another problem that I've been wrestling with for a while. I'm a Jeep guy, not a hot rodder (someday!), but I've exhausted the off road forums for a few dilemmas I've got... I can't wait to see how many other problems I can solve searching around here!

Quote:
Originally Posted by 496CHEVY3100 View Post
That is what I was thinking also .the bubble wrap will probably melt and I would keep a fire extinguisher close by as latex paint is flammable as is the bubble wrap.

the fumes from hot latex could be toxic also ,,,I would check before putting it under hood next to extreme heat. Just saying
This is one of my biggest concerns with many of these products. Not just that they're flammable, but many bedliners and asphalt-based products are VERY hard to put out once they start burning. I was relieved to see this post (which should be added to the wiki), but I will be doing my own test as well...
Quote:
Originally Posted by Hi Rise View Post
...One of the nice things about it as it will not burn. I sprayed 3 layers on a test panel. Let it cure, scraped some off held a match to it. The flames just dies out immediately It will not support combustion.
...
Brian.
Many thanks to Vince and all those who contributed here!
Billy
05-04-2014 05:55 PM
302 Z28
Quote:
Originally Posted by DADSSUB View Post
What about bed liner? Would it help with sound deadening?
Not a good alternative as it has very low heat dissipation and dries way too hard.

Vince
05-03-2014 03:53 PM
Mrrman Watching this thread...the lizard product is way overpriced so I always avoided it.
10-13-2013 07:54 AM
DADSSUB What about bed liner? Would it help with sound deadening?
10-13-2013 07:51 AM
DADSSUB Is the Lizard Skin mixture for sound reduction or temperature reduction?
10-12-2013 08:51 PM
Big_John Following up on my post, I did my deck lid on my Chrysler today.

I mixed the micro-balloons I got from Wicks with a quart of Rustoleam latex paint. The mixture was thick, but still pourable. I removed the deck lid and striped out the lock etc. and taped all the openings except one access hole near the latch and the two holes where the hinges go in.

I poured the mixture in the three holes, and after sealing them with more tape, I then left it standing on each of its sides for a few minutes. As it dried, I left it in each position a little longer, spending most of its time laying face down.

When I was done, I removed the tape and propped it up on saw horses face up and let it drip for a while. To my surprise, not a lot of paint dripped out.

Got it cleaned up and put it back on the car later. First thing I noticed was the trunk closed with a much less "tinny" sound. When you knock on the sheet metal, it almost sounds like knocking on fibreglass, rather than the steel panel.

So.... I'd say it worked. If I were to do it again, I would mix up more than a quart of paint, but that's the only thing I would do different.
10-03-2013 05:50 PM
hduff The top ten reasons are: COST.

Those insulating glass microspheres mentioned can be added to any paint.
10-03-2013 03:15 PM
DADSSUB Not that old of thread so I'm hoping people area still paying attention to it.

Was interested in finding out what the results were if you used some other paint instead of house latex. Our fab shop has a really nice primer they put on industrial duct work that I am planning on using inside my body.

I'm also a little confused why you would put the home made lizard skin over Dynamat? Don't they both do the same thing?
09-15-2013 12:42 PM
Big_John
Quote:
Originally Posted by herb58 View Post
do one test panel first using outdoor latex. or alkyd enamel better .at menards for 24 bucks a gallon. keep us posted on test
I'm thinking of using Latex just for ease of cleanup. I'm thinking this will make a mess.
09-15-2013 10:37 AM
herb58
test

do one test panel first using outdoor latex. or alkyd enamel better .at menards for 24 bucks a gallon. keep us posted on test
09-15-2013 08:27 AM
DanTwoLakes I'm sure nobody has, but give it a try. What do you have to lose? At worst it doesn't work, but if it quiets the car down even a little, it will be worth it.
09-15-2013 07:55 AM
Big_John This is a great thread that actually brought me here to lurk several years ago. Time for me to ask a question....

Has anyone ever poured the home brew Lizard skin into a panel opening and then rotated/turned/spun the panel to cover the inside?

I have a 70 Chrysler 300 vert that I want to quiet down. This car has the most highway noise of any of the big Mopars I've owned over the years. A lot of it seems to come out of the trunk area. The quarters were replaced sometime in the car's early lifetime and the usual heavy factory applied undercoating on the inside of the quarters is missing. I'll apply the Lizard Skin there and on the trunk floor.

I think I'd like to coat the inside of the deck lid too... but there is only some openings around the latch and hinges. I'm thinking I can take the deck lid off and pour some of the paint mix in the holes and twist and turn the lid until it's covered inside.

Has anyone done this??
09-11-2013 08:05 PM
496CHEVY3100 I had some extra Dyna mat left over so I put some on my fuel cell corners since is is only about 6 in from my exaust,,not that I thought it would catch fire ,,but to help prevent vapor lock

don't know how it will stand up to the weather ,
09-11-2013 07:44 PM
Chopchop Thank you.

It's probably not the best stuff you could put a couple inches away from a turbocharger but it seems to hold up pretty well to the temperature!
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.