Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Help with timing Chain and timing cam install
User Name
Password
lost password?   |   register now

Thread: Help with timing Chain and timing cam install Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-08-2006 10:01 PM
Blazin72 Did you mean timing gears instead of timing cam or did you mean a full camshaft swap?

If in fact you are going for a full-on cam replacement you're in for a lot of work. It's not hard to do but it is somewhat time consuming. Not only do you have to pull the intake, distributor, valve covers, lifters and pushrods you also have to pull the water pump, harmonic balancer, drop the oil pan and pull the timing cover. You may also have to lift the engine out of the engine mounts with a hoist to allow room to drop the oil pan enough to pull the front cover, this is a good time to replace the oil pan gasket. You're probably also going to have to pull the radiator and maybe even the grille to allow enough room to swap out the cam. If you have air conditioning then you're going to have to pull the condenser and probably the compressor as well. If you do have air conditioning then the refrigerant will be R-12 and it is illegal to vent that stuff to the atmosphere which means you're going to have to pay somebody to recover the refrigerant. Plan for two days to do the job, if you get started Sunday then the chances are pretty good that you won't get it done.

A timing chain replacement won't take nearly as long but you should still plan on dropping the entire oil pan in order to replace the oil pan gasket. You're going to go far enough into the engine that it would be a good time to change it out, especially if it's leaking. Give yourself the entire day for this job just in case you run into any unexpected problems.
12-08-2006 08:15 PM
T-bucket23
Quote:
Originally Posted by 327NUT
From what I understood you are just changing the timing chain and gears???
Title reads
"Help with timing Chain and timing cam install"

Its a lot different if it is just the chain and gears
12-08-2006 07:44 PM
327NUT From what I understood you are just changing the timing chain and gears???
12-08-2006 07:40 PM
T-bucket23 Make sure to not let any crap fall into the engine. You will have both the front and top open and will have a lot of gasket clean up to do. One work of advise is to just throw away the front an rear intake rubber gaskets and use a nice 1/4" or so bead of RTV black or blue. Clean everything well before re-assebly. Use Quality gaskets, cheapos will end up costing mre in the end. Follow the breakin instructions for the cam to the letter. It is real important to get the engine started with minimal cranking so make sure the distributor is close enough to start right up. It is a big job to change a cam, not hard but a lot of stuff to take apart. You usually will need to pull the radiator and condenser (if equipt)also.

good luck and let us know how you make out
12-08-2006 07:25 PM
327NUT No real tricks, just read the R&R section, you'll need a harmonic balancer puller, and a gear puller for the crank gear. Make sure the dots on the crank gear and cam gear are at 12:00 o'clock and 6:00 o'clock respecfully by ticking the starter till they line up vertically before you remove the cam gear. You'll also need a harmonic balancer installation tool, DONT beat it on with a hammer.
12-08-2006 06:48 PM
LXZ590 I do have the repair manual for the engine, I just wanted to know little tricks and stuff like that.
12-08-2006 06:44 PM
327NUT I strongly suggest you beg, borrow or buy a motor manual for your particular engine and read the timing chain R&R section before you even attempt to tear into it. It isnt hard, but if you have never done it before and are not very familiar with engines then I believe you would be in over your head. Or..get a knowledgeable person to help you, good luck
12-08-2006 06:24 PM
LXZ590
Help with timing Chain and timing cam install

So, before I do it on sunday wanted to find out how to do it and what is involved in doing it. I have a new timing chain with timing cam, the old one I beleive may be original like most of the things I replaced this far. the seal behind the cam and on top of the oil pan has been long gone. So on a
1984 Camaro z 28
305 Vin H
4bbl Quadra Jet
how hard should it be, what is envolved, and how long. Do you think that after replacing this it would run better. Thanks
Rich

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.