Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Engine heads
User Name
Password
lost password?   |   register now

Thread: Engine heads Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-01-2007 02:40 PM
Cesar Ruvalcaba No, bought the parts at the local autoparts. at the time, i though my block was a 350 so i requested 350 parts. when the engine was complete and operational i noticed i did not have the power i should have an a 350 so i inquire using the engine block id number and to my disappointment, found out the block is a 283. all the parts fit well and the engine runs smooth, but no where near the power of a 350. very low torque. you might wonder why i did not know, it is because i had just purcharsed the car from a friend. the car had 350 emblems which mislead me.
02-01-2007 02:25 PM
xntrik
Quote:
Originally Posted by Cesar Ruvalcaba
okay i

I had a 283 block rebuilt about 2 years ago with 350 parts. i did not know it was a 283 until i had completed the rebuilt and installation and all the parts where purchased for a 350 unknownly.

.
How did you get 350 parts into a 283 block?

I believe that you are mistaken.
02-01-2007 10:18 AM
Cesar Ruvalcaba okay i think i got most of my questions answer regarding heads. one more advise from you experts out there. I had a 283 block rebuilt about 2 years ago with 350 parts. i did not know it was a 283 until i had completed the rebuilt and installation and all the parts where purchased for a 350 unknownly. i just purchased a rebuilt 4-bolt main 350 long block. due to shortage in funds, i plan on using my accesseries which i used on the 283 for the mean time. accesseries inlcude, lifters, push rods, oil pump and distributor. the distrubutor is equipped with Frame Trower equipment. Should i proceed with my plans or should i cancel and wait.
01-31-2007 05:55 PM
BOBCRMAN@aol.com They will bolt to your block. But you must use an 88 or later style intake manifold.
01-31-2007 01:53 PM
Cesar Ruvalcaba I plan on using this heads on a older block (67-70). i will put this engine on a 69 Malibu. because this are newer heads, can i still use they on this block?. i do use my Malibu as a daily driver. no high performance yet.
01-31-2007 12:22 PM
Hippie Those are the "swirl port" heads used on Throttle Body Injected 305's and 350's. They are "okay" for a daily driver or cruiser but are not a great high perfromance head especially above about 4,000 RPM. Good heads for a heavy car or truck, they should deliver good throttle response and fuel economy if used with a near stock cam and 4 barrel intake. They have 64cc combustion chambers so they need a dished piston in a 350 to keep compression down. The engines they came on had electronic fuel injection and computerized timing with knock sensors so they could get by with higher compression.
01-31-2007 10:44 AM
Cesar Ruvalcaba Will this heads provide enough for this engine? also, can you provide some information on cc. the higher the cc the better performance etc??. what is the compression affect on heads.
01-31-2007 10:05 AM
johnnya From Mortec.com:
"14102193...87-up...305/350......1.94"/1.5" valves"
(1.94"diameter intake valve head, 1.5" diameter exhaust valve head)

No combustion chamber volume was listed, but I'd think they're somewhere in the 64CC range if they were used on 305's & 350's.
JA
01-31-2007 08:32 AM
Cesar Ruvalcaba
Engine heads

i have just purchased a 4 bolt 350 block (3970010) with modern heads (#14102193) the book list 1.9" to 1.5". what does this unit of measure represent? does anybody know how many cc? will this work well on my block? i looking for smooth performance but want to get the best out of my block. please advise.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.