Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> 48 chevy truck hood dont fit
User Name
Password
lost password?   |   register now

Thread: 48 chevy truck hood dont fit Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-14-2007 11:37 AM
CARGUY ill try to get some pix posted, again thanks for the help
02-14-2007 08:05 AM
kruzr I'd like to add a little to already good comments.
If you don't have truss rods,use (temporary) turnbuckles from your local hardware store.they'll pull it in closer for you.I've used thicker plates at (behind)anchor points to pull more evenly.You could also consider widening hood where it gets narrower(try temp wedge inside hood sides)Like mentioned before you prob have to add shims to cradle etc., tweak it and have lotsa patience,good luck
any pics of it?
02-13-2007 08:18 PM
fleetside66 I restored a '47, which I drove for about 7 years & a good friend still has his '50. One thing we both found out is that you will never get the hood right (aside from a very high end resto). It's the nature of the beast. Check out all of the other trucks like yours at the shows & you'll see that none of the hoods are perfect. A lot of them have paint chipping off where the hoods touch the fenders. Go with the flow & be happy with the fact that you've done your best with in inherently flawed situation.
02-13-2007 04:54 PM
Chopt 48 I found out the hard way that you have to have the doors fit perfect before you ever think about chopping one. I did chop it an run it a year before I did the suicide doors. That helped a bit.

Also make sure you have the proper support pad between the radiator support and the frame.
02-13-2007 12:14 PM
MARTINSR I recently sent this guy (click here) $100 for a frame. Now mind you, I havn't picked it up, but he seemed pretty trustworthy after a few phone calls and emails. I have a buddy who is going to go pick it up for me.

Brian
02-13-2007 11:24 AM
CARGUY thanks for the advice im now on the hunt for some truss rods
02-13-2007 08:00 AM
MARTINSR You have no truss rods, so of course it is going to be hard. It would be like adjusting the doors with bent hinges, it just ain't goin to work.

Get those rods and you will be surprised. As Chopt pointed out, there are other factors that could need to be addressed as well. But FIRST lets get those truss rods.

Brian
02-13-2007 07:44 AM
CARGUY id be happy if mine fit that good, i thought getting the doors right was bad but this is worse
02-13-2007 02:36 AM
Chopt 48 That thing will flex and squeek like a maniac without them. And never will stay in adjustment. The drivers side of the hood usually has a gap between it and the fender. Factory flaw. It gives the truck that bit of a snarl on that side. I've fought with mine for years and never had it perfect. If the truck is subframed it is that much harder to get the sheet metal all aligned.

This is about the best I ever had mine and it wasn't that close then.


The truck was sitting on a 67 Camaro subframe in front and it was hard to get everything just so. I am sure it wasn't.
02-12-2007 07:32 PM
CARGUY thanks, i don't have the truss rods is there any way around them i see a lot of people don't use them, if not guess ill need to find some thanks for the help
02-12-2007 01:16 PM
MARTINSR What you need to do is loosen the grille bolts and the upper fender to rad support bolts. Then tighten the tension on the truss rods that go from the fenders to the firewall. That is all it takes to move the fenders in.

Brian
02-12-2007 11:51 AM
CARGUY
48 chevy truck hood dont fit

im putting the front end back together on my truck but the hood wont fit it fits good everywhere except the front. when together and the hood is closed it looks like the front fenders are to far apart the hood fits good at the cab and along the fenders until about half way and then the gap starts to get wider on both sides. the inner fenders, radiator support, and grill all are installed,soi don't know how to get the very front of the fenders in any more than they are now,any 1947-1954 chevy truck guys out there?thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.