Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> what lenght pushrods? wiped out cam? 78 ford 302
User Name
Password
lost password?   |   register now

Thread: what lenght pushrods? wiped out cam? 78 ford 302 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-19-2007 11:26 AM
KULTULZ
Quote:
They had a real hard time starting the motor, cranking it over many times for probably more than 30 min., and after it finally fired and ran, I was surprised to see they reved it up past 4,000 many times and did not break it in at the as recommended holding at 2000 rpm. They then shut it off after about a minute of running. They did this about 2 times after it cooled. start reved up high for bout 1 min. and shut off. THEN he said they "broke" it in.
Well, the extended cranking cleaned off the assembly lube and the 4000 RPM bursts with too soon shutdown took care of what was left...
03-19-2007 09:00 AM
red65mustang SBF cylinder heads up to about mid year 68' had fully adjustable rockers and shorter (6.8") push rods
the non adjustable 76' heads have "bolt down" non adjustable rockers and do use the longer rods with shims if necessary (6.9"approx)
tell him his valves are longer also than the adjustable rocker heads
I call it: "the L-4 change bear trap"

cause of what he did for the break in......he really should do a lift measure at the rockers on all 8 cylinders because: "some were loose and some were tight"
no calipers on hand, a crude way is to make a lift "reference stick" to compare all 16 valves at TDC...cut it/shape it so you can measure each at the same location on the head....wooden paint stick works...easy to cut and trim
03-18-2007 11:09 PM
Warrant
what lenght pushrods? wiped out cam? 78 ford 302

I have a friend with a rebuilt 302 out of 78 mustang ii. The motor is a stock rebuild (aftermarket flat tops, cam, intake, carb, everything else stock) with about 9:1 CR. The cam is a hydraulic 218* .488" lift, stock heads (no milling) and pro form alum full roller rockers(to work with stock push rods length).

They had a real hard time starting the motor, cranking it over many times for probably more than 30 min., and after it finally fired and ran, I was surprised to see they reved it up past 4,000 many times and did not break it in at the as recommended holding at 2000 rpm. They then shut it off after about a minute of running. They did this about 2 times after it cooled. start reved up high for bout 1 min. and shut off. THEN he said they "broke" it in.

They pulled the valve covers off bout a day later cause they heard some valve train noise. They found that the push rods are too short??? - they were loose and wiggling. But before they started they adjust the preload(weird ford type pedestal mount so you have to shim them) and he said that they weren't to short then. He also said that the ones towards the front of the motor weren't as loose or not at all. While the ones near back were looser.

Now to me this sounds like a possible wiped out cam??? he said he was using 6.8** length and now he needs 6.9**. If he indeed does need longer length could their be any damage done?

What do you guys think?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.