Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Roll & Pleat 52 Ford Headliner/Panels
User Name
Password
lost password?   |   register now

Thread: Roll & Pleat 52 Ford Headliner/Panels Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-26-2007 06:57 AM
DanTwoLakes That's what I thought you wanted to do, I just wasn't sure. You need to get the windlace installed around the doors first, which will require you to loosen the headliner in that area. Ideally, you should take out the old headliner. Do you have the old headliner? If not, buy an inexpensive headliner from someone like Kanter, ( www.kanter.com ) take it apart and use the pieces for a pattern. The windlace is tacked or stapled to fiber strips that surround the perimeter of the doors. Those metal pieces with the teeth facing the outside of the car around the top part of the door should unscrew, and there will be tacking strip underneath. The tacking strip is held in place by metal "V" shaped teeth. If some of the tacking strip is missing, it needs to be replaced. You can replace missing sections with strips of black waterboard glued together to make the width and thickness you need. After the windlace is installed, put the metal strips back in and the headliner gets tucked up underneath in that area. Do the headliner the way you want to do it, with the pleats running side to side. Matching the pleats front to back could be a real headache. Check out the knowledge base for more detailed instructions in hanging the new headliner.
03-25-2007 09:57 PM
52HEMI
Interior Headliner

I plan to use the original bows that came with the car. Roll & Pleat is the term I grew up with. It means cutting the vinyl into 1 &1/2 inch strips-plus1/2 inch on each side for the seam (alternating white and purple stripes) and sewing them together with listing cloth sewn in where the bows cross the top of the car. I would prefer for the stripes to go from side to side, but have heard that it can be impractical. I also plan to use a wider strip of vinyl, front and rear, to finish extending the headliner to where it is glued to the metal of the car and down the rear quarter in front of the rear glass. I am also unsure how to fasten the windlace around the door - is it tucked in up over the door the same place the headliner is pushed in, or somplace else? I'm also not sure where it goes on the rear of the kick panels. As I said, I apologize for my stupidity, but I've never done a headliner before. All help will be appreciated beyond imagination! See 52HEMI Journal for Photos.
03-23-2007 09:22 PM
DanTwoLakes I would love to help you, but I'm not sure what you want to do. Do you want to install a "hard" headliner or use the bows that came in the car? I think that's the reason you haven't gotten any replies up until now. I'm perplexed, (and I think everyone else is too.) Please explain better what you want to do. The problem is "tuck and roll" , or "roll and pleat" means different things to different people. ???
03-21-2007 09:36 PM
52HEMI
Roll & Pleat 52 Ford Headliner/Panels

I am going to attempt to sew and install my first roll & pleat headliner and door/quarter panels in a '52 Ford Clb Cpe. Anyone that has photos and instructions and would be willing to assist me with same would be greatly appreciated. Should the stripes in the headliner go lengthwise or crosswise? I plan to put a single color wide strip at the windshield and rear glass to make it easier to stretch and install. Again, photos, instructions or help of any kind will be most greatly appreciated (and Needed!!!). Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.