Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> lower control arms
User Name
Password
lost password?   |   register now

Thread: lower control arms Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-02-2007 05:49 PM
rebelbill1972
re: lower control arms

I've got the pictures but they are too big to load. Anyone who needs to see them can PM me with your e-mail and I will gladly send them to you. I'll try to take some more pics at a lower resolution and load them in the next couple of days.

Bill

I put the pics of the tool I made for seating ball joints in the lower control arm on a newer model F-150 in my album.

I made this because the regular press would not pull the new ball joint into the control arm properly. I was told to set a piece of flat bar on top of the control arm and try, but the bar sat at a bad angle and didn't look too safe. I set this one(in the pics) on top of the lower control arm and used the press to pull the ball joint into place. The small piece of pipe welded on top keeps the clamp from shifting and the big one on the bottom sets over the hole.

I can't find the one I made to push the ball joints out with but it was the same except the bottom pipe was smaller in diameter and about 2" long. Using the ball joint press it will push the ball joint out without damaging it.

Let me know what you think...

Bill
04-30-2007 08:50 PM
runn141
Quote:
Originally Posted by Triaged
Are you sure you still have both coil spring isolators in the frame spring buckets? If you lost one that end would sit lower.
i have no isolators on either side, just something to cause rust. i guess i could use one on the lower side though.
04-30-2007 07:07 PM
Triaged Are you sure you still have both coil spring isolators in the frame spring buckets? If you lost one that end would sit lower.
04-28-2007 06:58 PM
runn141 i would appreciate that
04-28-2007 06:56 PM
rebelbill1972
re:lower control arms

I was doing ball joints here in the shop not too long ago and after installing the new ones I found a crack in the lower control arm. I had one of the Boilermakers weld a 2 1/2" piece of pipe(diameter just enough to rest on the edge of the ball joint) to a piece of 3/8" plate cut to a near triangle shape so it would sit level in the space I had to work with and get a straight shot on it and used a hydraulic press to push it back out.

I don't have my camera with me tonight but if you want I'll bring it tomorrow and try to post some pics...

Bill
04-26-2007 09:53 PM
runn141
lower control arms

i have an 87 s10 i have been building from the ground up. i installed new urethane bushings and new ball joints. now i have noticed that they do not match(lower control arms) and one is very pitted from rust(when i installed them they were all i had at the time) and one is letting the truck set 1/2 inch higher . now my ? is, is there a trick to get the ball joints out and reusing them? as for bushings they shouldn't be a problem, unless anyone has a suggestion

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.