Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Cutting Glass on a '56 Buick
User Name
lost password?   |   register now

Thread: Cutting Glass on a '56 Buick Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-30-2007 09:06 PM
60tbirdrick Thanks TwoChops. Thats what I was thinking would be the easiest way. You wouldn't happen to have any pics of the brackets you made to hold the windshield in place do you?
04-30-2007 06:25 AM
Cutting Glass on a 56 Buick

60 tbirdrick --
On my 57 Buick the windshield and 3 piece rear window were
both sunk. This was done by cutting a slot in the metal edge
at the bottom of the glass so that it can slide through. Make
new brackets to hold in place. The only glass that had to be
cut was the rear quarter window and vent window glass. The
door glass remains stock and has a stopper added to prevent
the glass from being rolled too far.

04-29-2007 05:49 AM
60tbirdrick TwoChops,
How did you sink the windshield with the wiper drivers there in the way? I want to do this to another 60 T-bird that I am building. Do you have any pics of doing the windshield? I think I have an idea of what I want to do but I'm not sure of how to set and secure the seal which is what holds the windshield in place. Did you sink the entire windshield frame down or just cut it down and sink the windshield? Thanks.
04-28-2007 09:53 PM
Bryan59EC TwoChops---
Too cool for words----looks nice

04-28-2007 09:19 PM
cutting glass on 56 buick

I just finshing a chop on a 57 BUICK,All my glass was sunk ,looks
like it was factory job.
04-15-2007 09:26 AM
MARTINSR Mark, tempered glass can not be cut, period. 99% of all curved glass is tempered, windshields being part of that 1% that is ALWAYS "Safety plate" (the two layers of glass with plastic in the middle). I am not certain of the actual process of manufacturing tempered glass. But as the name implys after the glass is formed into shape it is "tempered" with heat to have a "layer" of super hard glass on the outside. When that super hard layer is penatrated, the ENTIRE sheet "fails" and the ENTIRE sheet falls apart into tiny 1/4" sized pieces.

It is strange stuff, you can throw a brick at one of these windows and it MAY bounce right off! OR, you can take a tiny piece of ceramic from a spark plug and throw it at it and it will break into a million 1/4" pieces! That is a little trick if you ever have one to break, a tiny piece of spark plug ceramic WILL break it almost every time!

The 56 Buick (as in all GM cars) had a safety plate windshield and side glass with a tempered back glass. The side glass is all perfectly flat by the way. There is no car made today that has this, all glass but the windshield is tempered on 99% of cars today. There are a few exceptions in high end cars and cars with side air bags (a very few) that have curved safety plate on the sides.

I did a little Mythbuster experiment on sandblasting tempered glass on this thread. Urban Myth?

It can be ground with a wet belt. I know a glass guy who converts 65 Mustang Coupe door glass to Convertible glass by grinding the rear corner down a little. But it literally takes DAYS to do it, grinding a tiny amount every day.

Nope, cutting the curved tempered glass has been the "Holy Grail" top choppers have been searching for since the first car with it was chopped.

04-15-2007 05:06 AM
41International I would think any kind of glass can be cut. My wife does stained glass and has a saw to cut glass. It is called a ring saw and has a ring about 6 in. in diameter for a blade with dimonds glued to it. The blade is expensive about $100 and the saw cost $500 I think. I would think a good glass shop would have some kind of saw. If the glass is lamanated the plastic in the center might gum up the blade not sure never tried it. Good luck Mark
04-13-2007 06:34 PM
MARTINSR The back glass can not be cut, it is tempered. The windshield, there are people who can cut it without a problem.

04-13-2007 06:23 PM
BLOWN 1100 Yes the curved glass can be cut but very few people can cut it. A friend
of mine had one cut for his chevy pickup. I have the guy's name and
phone no. in Big Springs Tx. if you need it.
04-13-2007 06:02 PM
Cutting Glass on a '56 Buick

i've never heard of anyone succesfully cutting glass for a chop top on a 56 wrap around. Has anyone ever seen it done? if not, i've seen a few chopped '56s; new glass? sink existing glass into body?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 01:14 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.