Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Interior Door Trim
User Name
Password
lost password?   |   register now

Thread: Interior Door Trim Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-15-2007 10:13 PM
horvath Awesome.

Thanks guys!
06-15-2007 01:45 PM
DanTwoLakes That is very nice work. Alan: Here's another tutorial for you: http://www.hotrodders.com/forum/fibe...ghlight=fleece
06-15-2007 11:47 AM
37FordLS6
The Process

1: The foam is available at Lowes or Home Depot. It comes in different thickness so pick the one that will suit your project best. Cut the ruff shape with a utility knife the start shaping it with 80 grit sand paper on a sanding block.
2: You have to use epoxy to coat the foam as fiberglass resin
will immediately eat the foam! I found my epoxy (medium set)
at Boater World made by MAS Epoxy. You will also need fiberglass cloth which is much easy to use than fiberglass mat.This is also available from the marine store or on ebay.
3:Mix the epoxy as indicated (try not to waste it, its expensive) and spread it on the foam with an acid brush. When its all coated place your glass cloth over it and apply more epoxy. Once its dry block sand it lightly. At this point
I use body filler and sand reapplying filler till its smooth. I then prime it and apply a guide coat and sand with 180 grit
and repeat this again until there are no low spots and then finish with 320 grit. Its then ready for you paint finish.
06-15-2007 10:46 AM
horvath If you have pics that show your process, step by step, like a tutorial, I'd sure love to learn how to do what you do!


I'm thinking about incorporating my interior window trim into the top of my door panels to make them one piece ... fiberglassing may be an answer but I've never done it before. What you did with your top panels came out really nice!!!
06-15-2007 09:53 AM
302 Z28 I have a console design firmed up in the flesh, but I am not too pleased with it. It takes up far too much room in my 34 3 window. I think I can slim it down a bit. I need to put the radio, A/C controls, ign switch, headlamp switch, 12v power plug, and door window switches in it. I may decide to reroute the door window switches to the door panels, but that requires more wires to run to the back of the passenger compartment.

Vince
06-15-2007 09:09 AM
37FordLS6
Thanks

Thanks all for the kind comments. I'm in the process of doing the armrests and will post some pics of those soon.

Vince,
I changed the design of the center console to the one pictured. Been putting off finishing it as I don't have a radio for it yet and I'm still not decided on how to finish it. I will probably paint it black with an aluminum face.
Thanks
Bill
06-15-2007 07:28 AM
302 Z28 Very nice work on the door panels, please post more pics as you progress. I am currently at this stage in my build and I am looking for all the ideas I can find on door panel design. I really like what I see in your work.

Did you change the design of your console? I was looking at your photo gallery and there are some pics of a fiberglass console that look different.

Vince
06-14-2007 09:49 PM
astrophel That looks great! Well done!
06-14-2007 09:35 PM
horvath Awesome!
06-14-2007 05:09 PM
37FordLS6
Interior Door Trim

The car came with a very narrow and square finish at the top of the door on the inside. Not only would this not look good but would also be uncomfortable! So, I got foam insulation from Lowes and cut and formed then to the shape I wanted.
I then covered them with fiberglass cloth and epoxy and then
the fun began. Lots of sanding and filling to get them straight but I think it was worth the effort. A few coats of black with some wet sanding in between should give me a mirror finish.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.