Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> roller cam
User Name
Password
lost password?   |   register now

Thread: roller cam Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2007 02:01 PM
oldbogie
Quote:
Originally Posted by chevrolet327
can i put a roller cam in a old 1963 small journall 327 and did somebody know if is realy better than a flat tappet cam
I guess all this comes to what are trying to build?

Unless youre racing, such a conversion is expensive and probably doesn't net enough gain against the cost for an aftermarket roller and complication to convert to a factory roller, which will still require expensive after market lifters.

Bogie
07-10-2007 06:20 AM
baddbob The aftermarket is making some good rods for the small journal engines, I put Eagle H-beams in my Son's 331 and they have huge 7/16" ARP bolts. Another thing that helps the older engines is good quality maincap bolts or studs. Solid Roller lifters and springs really aren't all that expensive if you shop around, check out Competition Products for some good prices.
07-09-2007 09:57 PM
DoubleVision Having what installed? You can install the adapter yourself. This is the same thing I`m about to do. I have a 96 Vortec block I`m dropping a 68 307 crank in using a adaptor. I`m also using 5.940 rods out of a 95 L99 4.3 V8 "Baby LT1" as there called. I didn`t say he had to do it, I just said it`s what I would do. I bought a vortec engine years ago complete for $300, I could have stabbed a cam in it and intake swap and been down the road, which would have been cheaper overall than buying the whole works to set up a roller cam in a small journal block then praying everytime I revved it that it wouldn`t come unglued. But, to each his own.
07-09-2007 08:57 PM
ericnova72
roller cam

I realize you can with an adapter, but it's pretty expensive, just so you can use a cast crank from a large journal engine. Also, what about the cost of having it installed? The whole idea is getting pretty expensive for no more motor than you're going to have when it is done.
07-09-2007 07:52 PM
DoubleVision Sorry Eric, you can with a 2 piece seal adaptor.
http://store.summitracing.com/partde...5&autoview=sku
07-09-2007 06:28 PM
ericnova72
roller cam

Sorry DoubleVision, you can't put the 307 crank in the '87 and newer block because a 2-piece seal crank won't go into a 1-piece seal block.
07-09-2007 06:21 PM
DoubleVision For what you`ll spend on lifters, retainers, pushrods and camshaft, it would likely cost the same to find a 1987 or later 350 with a factory roller cam. Then find a 307 crankshaft, have it balanced, throw it in the 350 block and use 327 pistons and you have a 327 with the benefits of you`ll just have to buy the cam, not the whole kit, and the large journal blocks came factory with stronger rods. Speaking for me, this is how I would do it, my reason being I trust small journal rods about as far as I can throw a anvil. Or you could just stick with the straight 350, slap in the cam, add the correct valve springs and be on your way.
07-09-2007 06:07 PM
Jmark The aftermarket roller lifters will fit fine and you will love em! someday standard lifters will be obsolute! LOL Less wear, less friction, can handle more agressive ramps and cam lobes don't go south during breakin. Best of everything, except the $$$$ for a set!

Mark
07-09-2007 05:54 PM
chevrolet327
roller cam

can i put a roller cam in a old 1963 small journall 327 and did somebody know if is realy better than a flat tappet cam

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.