Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> engine pinging
User Name
Password
lost password?   |   register now

Thread: engine pinging Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-21-2007 09:26 AM
JG700 Good news! After getting tdc on #1 timing marks lined up, but rotor was past #1 tower. I reset it to line up, reassembled, started the car, and NO PING! A bit sluggish off the start, but set at 12btc, whereas before I had to turned it back to 5* just to minimize the pinging. Don't know how that happened, unless I installed it off the first time. Thanks for the help!
07-15-2007 11:42 AM
JG700 Another find: rebuilder installed 1.94 intake/1.50 exhaust valves (new). L-82 version of the 350 (which is what I have) had 2.02 intake/1.60 exhaust valves. Could this be the cause of the detonation/pinging problem?
07-15-2007 09:06 AM
JG700 Car had r45ts, so plugs are virtually the same. New info: I checked the spec sheet from my engine rebuild: they replaced my stock cam with a "mild" cam with the following specs: 214-224 443-465. Is this appropriate for my set up? (1980 Corvette L-82 SB350. Q-Jet, auto tranny, stock heads,new valves 1.94 intake, 1.50 exhaust, 3.07 rear.)
Again, I'm having trouble with detonation and have to turn the timing way back (from 12* to around 6*) to minimize it. Could the problem be this cam set-up? Thanks! JG700
07-14-2007 11:38 PM
baddbob What heads are on the motor? I believe the R44TS? is a longer reach plug (for the later design heads) than an R44T and if you're using the wrong length plug the exposed threads could be glowing hot and causing the spark knock-possible. Check it out.
07-14-2007 04:08 PM
JG700 OK, so here is the update: I rejetted my carb from 74 to 77; replaced the distributor springs with thicker ones; set initial timing to 10*(from 12*); replaced spark plugs with colder ones (r44ts). Engine STILL knocks/pings under load. Could I have installed the distributor wrong? As in, off by a tooth? It idles great, and runs smooth under easy acceleration. Could it be the EGR valve? Confounded and frustrated now! Thanks. JG700
07-12-2007 09:37 PM
baddbob Put in R43 plugs, 42's will also work just fine but they'll take awhile to warm up when first starting the engine cold. I've got a 350 running pretty lean with poor (.065) quench distance and it likes the 42's.
07-12-2007 05:53 PM
oldbogie
Quote:
Originally Posted by JG700
Hello. Recently (100 miles) rebuilt 350 sb bored 30 over, mild cam. Auto tranny. Car runs great, except it pings upon hard acceleration (like from a dead stop.) Sounds like a lot of marbles rolling around, small popping sounds that eventually stop after the car gets up to speed.I had the q-jet rebuilt also. I tried retarding the timing from 12btc to 8 btc, and had the carb jets increased from 72 to 73 because it was running very lean. Still pings/pops. What else can I do? Would further increasing the jets help, or adjusting the timing back again? Any ideas/suggestions would be greatly appreciated! JG700
I read thru all these responses and what you're doing and am left with questions leading to more definition.

- The car is a what?
- How heavy?
- What is the transmission (besides being and automatic)?
- What is the rear axle ratio?
- What is the tire size?
- Do you have the cam specs?
- Do you know if the cam gears and chain were timed correctly?
- Is the cam installed with and advance bushing?
- Do you know how much total advance the distributor has, base plus variable which is the centrifugal and or vacuum)?
- Do you know how fast the variable comes in as well as how much?
- Do you know if the original valves were reground or replaced (I'm assuming this is a rebuilt 350 replacing a 350)?
- do you really know the static compression ratio (swept volume and combustion space volume/combustion space volume)?
- Is the carb the same as original to the engine?
- You've changed jet sizes, what about metering rods?
- Which spring is controlling the metering piston that moves the metering rods?
- Did you change the intake?
- Does the intake have a vacuum leak?
- What is the idle Vacuum?
- What is the vacuum under acceleration?

This breaks down into:

- Not enough gears for the weight of vehicle.
- Cam not timed correctly.
- Static compression too high, cylinder pressure measurements aren't a good indicator of this.
- The engine running lean:
- Vacuum leak
- Carb jets too small; metering rods too big; metering piston stuck, metering piston's spring not in synch with engine's vacuum.
- Secondary not coming in properly, there's cams for this and tuning packages for the air valve.
- Fuel pump not delivering enough pressure.
- Float not adjusted correctly.
- The plastic anti-slosh gadget above the needle valve left out.
- Plugged filter, pinched line.
- Too much or improper advance rate:
- Cam and crank not aligned properly.
- Cam too advanced with bushings or off set crank Woodruff key in gear.
- Ignition advance problems:
- The vacuum doesn't drop off fast enough as the centrifugal
comes up.
- The Damper and Timing marks on the timing case cover are
mismatched. Different years and models move these around so
just grabbing parts from here and there can get you into problems.
- The distributor just not installed correctly, or not wired correctly.

- Problems in the combustion chamber.
- Reground valves have had the margin ground too far making them run
hot on the remaining sharp edge.
- Spark Plug heat range too hot.
- Incorrect head gasket or position of gasket:
- Causing improper coolant flow.
- Combustion ring hanging in a chamber and heated to glowing.
- Too thin combining with decked block/milled heads to make
compression too high.
- SMOG open chamber head that when combined with dish piston
can't provide adequate squish or quench.

As you can see, you're just barely touching the possibilities. I can go further myself but need to get on with other things this afternoon, but this ought to be enough for you to cogitate on for a while.

Having to push the timing back speaks pretty loudly to distributor or cam setup issues. If the cam is too advanced you have to compensate by backing the timing down. You need to really know where the cam is relative to the crank. And I don't mean looking a factory alignment dots. You've got to get a degree wheel and TDC finder to know for sure. This isn't a 100% thing maybe not even a 50% thing, but in my so called mind, it's a strong indicator as a place to start looking.

Bogie
07-12-2007 05:22 PM
techinspector1 It is NOT ok to have a bit of pinging.
07-12-2007 02:38 PM
JG700 Switched to a colder plug (r45ts - r44ts). Checked balancer - at 0* tdc#1. With colder plugs, very little pinging (only on really hard acceleration/load.) Yes, timing checked with vacuum plugged, but thanks for reminding me! Should I go colder? Move the timing back a bit more? Or is it ok to have a bit of pinging? Thanks for all of the advice!
07-12-2007 01:42 PM
perrib
Rattle

Ok no more pinging. Is your total timing now within specs? Then everything should be ok
07-12-2007 01:40 PM
speedydude Just my .02.... I agree with Mr. Tech and my gut instinct is that your balancer is off a little. When you can retard back to 0 DEG and your pre-ignition goes away........my first place to look, if it were my engine, is establishing true TDC.

You could try the afore-mentioned stuff but I would want to be sure my timing marks are dead on. Check the weights on the advance and make sure they spring back freely.

I hate to even ask this but you do have the vacuum advance disconnected and plugged when checking the timing right??
07-12-2007 01:17 PM
techinspector1 JG, both DHMag and baddbob suggested changing to a colder plug. Toddle on down to Autozone and get the colder plugs and gap them properly. If using a traditional distributor with separate coil, gap at 0.035". If HEI, gap at 0.045". Pick up one of those little plug gap thingies they keep by the cash register. Looks like a large coin and has a hole to affix to your key chain. Do that and see what happens. Report back with your findings.

Yes, it is possible to retard the ignition.

The problem is that unless you've verified TDC on the outer ring of the harmonic damper where it lines up with the pointer on the front cover, then you are flying blind. Oftentimes, the ring slips on the elastomeric material that is placed between the damper outer ring and the inner hub. If that has happened and you haven't verified the true TDC, then any further attempts to time the motor with a light will prove futile.
07-12-2007 10:30 AM
JG700 OK. Retarded timing until the pinging virtually stopped under load. I'm now set at 0*. Initial timing was 12 btc. Is this a problem? Is there such a thing as too retarded (and I don't mean ME!) Or should I use colder plugs and increase the timing? Currently using AC Delco R45ts. Thanks!
07-12-2007 05:38 AM
baddbob Use some AC spark plugs in the 43 or 42 heat range, I bet that'll help the problem. You also might be able to switch to steel shim head gaskets if the piston to deck height is .020ish
07-12-2007 04:34 AM
JG700 If that's the case, what's next? Any solutions other than removing the engine and sending it back to the machine shop?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.