Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Build my 327
User Name
Password
lost password?   |   register now

Thread: Build my 327 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-03-2007 10:28 AM
454C10 3.73 is ok but I would use a little more stall. 2500 should be a good one to use with the 3.73. A 3.73 used with a 327 will lower the stall a few hundred rpm due to less low rpm torque and a higher gear. A 2000 stall will feel weak off the line.

A 3.73 with a 700r OD will yield a 2.70 top gear. Which is 2500 rpm at 72mph with a 26 inch tire. So, a 2500 stall should be ok. You can get that in a lock up converter also.

A 270H will make more low rpm torque and a 280H will pull harder on the top end. So, both cams will work fine, just choose the cam that better suits your needs. A roller will make more torque and hp but adds to the cost a lot. You really will have a hard time feeling the difference with the flat tappet versus the roller cam.

I'm thinking you will like the 270H better than the 280H. In both cases, use 10:1 cr with aluminum heads. 9.5:1 minimum. You will find it is harder to build compression with a 327. A 350 with flat tops and a 64 cc head is the perfect combo for you. A 327 will need domes to make that compression and domes are bad on flame travel. Plus the extra 1/4 stroke of a 350 makes a big difference. If you ever get a chance, use a 350 crank.

Also avoid the newer flat tappet cam grinds (xtreme, voodoo, ect). They tend to go flat quickly due to very aggressive cam lobes. The 270H and 280H grinds have been around for a lot of years and are already aggressive enough. And, use diesel engine oil with your new cam, as recommended by compcams if you use flat tappets.
08-03-2007 09:25 AM
chewyscool thanks alot 454c10 I found that article very informative and seeing about baseing my motor on the one in the article and your advice of alm. heads. Do you have any advice on the 3.73 gearing with a 2000 stall?
08-03-2007 07:07 AM
454C10 check out this article. 408hp 400ftlbs 327


http://www.chevyhiperformance.com/te...ine/index.html

However, I would use aluminum heads and more compression for better low rpm torque.
08-02-2007 04:14 PM
chewyscool I was thinking of gearing 3.73 with a LSD. I do want the torque and power in the lower rpms for street use. Thanks.
08-02-2007 01:24 PM
454C10 You are right. That isn't a cam for bottom in torque. However, he didn't ask for bottom end torque. He whats 400hp and neck snapping torque. That is what the gears and high rpm stall converter is for. The engine will not spend much time in the lower rpms and will have neck snapping torque in the upper rpms. Plus, it takes a good amount of duration to make 400hp with a 327. A short duration low rpm torque cam will fall very short of the 400hp goal.
08-02-2007 01:10 PM
383silverado
Quote:
Originally Posted by 454C10
Roller cam would help a lot to make more torque (225 to 230 degrees duration at 0.050, 108 to 110 LSA)


i don't think thats correct cam duration for bottom end torque. i think you need some thing like 210 or 212 intake duration @ .050 . the higher you go in duration the more the bottom end will suffer.

here is a quick explanation of how a cam works. scroll down

http://www.fierolt1.com/lt1_camdata.htm
08-02-2007 10:35 AM
chewyscool Thanks all I'm feeling better already!!!
08-02-2007 08:36 AM
454C10 Need gears (4.11's with LSD) and a 3000 stall converter

Better heads (after market, 64cc chambers, 160 to 180cc intake ports). 170cc Edelbrock Performer heads (not rpm) would be a good choice.

High compression with aluminum heads (10.0 to 10.5 cr)

Roller cam would help a lot to make more torque (225 to 230 degrees duration at 0.050, 108 to 110 LSA)

Edelbrock Performer RPM intake (not air gap) and a Holley 750cfm 3310.

Full length headers (1-5/8 tubes with 2-1/2 collectors)

You can make 400 ftlbs of torque and 400hp with a 327 but it will be in the upper rpms which requires a lot of gear and a loose converter.
08-02-2007 05:17 AM
red65mustang for "neck snapping torque" (400ft/lbs+) it's gotta be atleast 350 cube and 383 is a better choice....

here's a link from the Knowledge Base* link above....100 combo's of 350-383 motors with build spec and info source and "published" HP/TQ

http://ryanscarpage.50megs.com/combos1.html

*DO spend some time reading in the Knowledge Base...articles and tech info on A to Z for all parts of all cars broken down by catagories....
08-01-2007 11:52 PM
327NUT Pretty simple fix, you have a large journal 327, its the same as a 350 block so either put a 350 crank in it and have a 350 or buy a GOOD 383 stroker kit.
08-01-2007 09:23 PM
DoubleVision Sure I`ll build it, but your gonna pay me afterwards! ha.
You want 400 horsepower and lots of torque then the writings on the wall, get more cubic inches. While 327`s are outstanding engines, they have a shorter stroke and stroke is where torque is at. I`d suggest a 350, or even better, a 383 if you really want a torque monster. However, 400 horses from a 350 is easy as well. Your stock heads aren`t going to cut it, don`t waste your money on them. I`d suggest a set of vortecs or better, and a better intake also. Cam it accordingly matched with the compression ratio and carb size with a set of headers and your there. We need to know what the rear gear ratio is as gears play a big role in this. your goal of 400 horses and lots of torque is simple with a 383, and it`ll be a blast to drive and won`t break the bank.
08-01-2007 08:21 PM
chewyscool
Build my 327

I'm looking for advice, suggestions and comments for my engine build. I'm looking for around 400 HP and neck snapping torque for a weekend street 67 nova. I have 327 large journal (69') 481 heads, 365 Hp gm iron intake, and carter afb not sure about the cam. Most of these parts are for 60's vettes as per my research, its turning a 700r4, with stock 10 bolt. I'm not satisfied with the performance that I'm getting. I feel the car is sluggish although I have never taken it to a track. Feel free...............

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.