Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> rear main seal
User Name
Password
lost password?   |   register now

Thread: rear main seal Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-13-2007 06:14 AM
Notorious Not to worry, a 350 will not have a rope seal.
10-13-2007 12:22 AM
DHMag to avoid a leak, dont install the seal ends flush with the block/cap. an 1/8" offset is all you need.
10-13-2007 12:11 AM
artsman
Quote:
Originally Posted by karl1
i want to replace the 2 pc rear main seal in my 350 without removing the crank. how do i do this? what kind of seal works best? thanks
You did say if the engine is in the car. If it is and the cross member is in the way of dropping the pan, you will need to remove the thru bolts from the motor mounts, the trans mount bolt and jack up the engine about 3-1/2 inches using a piece of 2X6 or other block of wood between the jack and pan, after raising the engine, put the thru bolts back in the mounts and it will hold the engine up.
You will probably need to remove the fan or shroud. Rotate the damper so the timing mark is at the bottom, this will allow the pan to clear the crank. Remove starter, pan bolts, oil pump and rear main cap. The top half of the seal can be removed by tapping the end of it with a soft punch and grabbing the other end with plyers. The new seal should come with a thin piece of plastic to insert part way into the top half of the seal recess so the new seal can slide past it to avoid damaging it on the sharp metal edge. There is a flat spot on the cap next to the seal that requires a thin amount of sealer. Oil the new seal and install it so the ends don't line up with the main cap split, about 1/4 inch should work. Don't know if one brand of seal is better than the other. I would recommend a Felpro one-piece pan gasket. You really should get a shop or repair manual of some kind that covers this job. Torque spec for the main cap is 70-85 ft lbs and 60-70 ft lbs for the oil pump.....Doug
10-13-2007 12:01 AM
scholman Karl1,

I have done this many times, back in the day.

Pull the pan off and take the oil pump off of the rear main cap. Watch out for the oil pump drive shaft. I put the pump in the pan for safe keeping.

Now take the two bolts out of the rear main cap and remove the cap. Taking the old seal out of the cap side is a snap, it is the engine side that gives people head-aches.

If the old seal is a rope seal then you will need to screw in a very thin and long eye bolt for wood. Then grab the eye bolt with a screwdriver through the eye and as you pull the seal have a friend rotate the crankshaft in the same direction. It may want to fight you but just remember it is just rope so you will win the battle.

If the seal is one of the new neoprene seals do the same steps but just look out for the metal in the seal and you will get this one out too.

Replace the old seal with the newer style neoprene style they are much easier to install than the rope. Be sure the lip faces toward the engine so it will not leak.

When I replace the main bearing cap I spray the mating surfaces with some 3M High Tac spray. Then re-torque the bolts to 65 pounds feet. Install the oil pump making sure the oil drive ligns up with the bottom of the distributor. Then tighten that bolt to 40 pounds feet of torque I think. Check these specs to be sure I am correct, it has been a long time you know.

Have Fun
scholman
10-12-2007 10:11 PM
karl1
rear main seal

i want to replace the 2 pc rear main seal in my 350 without removing the crank. how do i do this? what kind of seal works best? thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.