Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Removing-Reinstalling Valve Springs - Help
User Name
Password
lost password?   |   register now

Thread: Removing-Reinstalling Valve Springs - Help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-18-2007 01:22 PM
454C10 There is also the poor mans method, which consist of stuffing about a 1 foot of 1/4 inch diameter soft cotton rope into the cylinder through the spark plug hole. But first place the piston at tdc. The rope will hold up the valves while you mess with the valve springs and retainers.
10-18-2007 01:05 PM
engineczar Sometimes I use an air compressor, sometimes not. If I do I run just enough pressure to hold the valve closed but not enough to turn the engine. Knock on wood I haven't lost one yet and I've changed more sets than I care to count.
10-18-2007 12:32 PM
454C10 So, I guess you have an air compressor.

You can use a compression tester hose to fill the cylinder but first you need to take the valve out of the hose. Just use a tire valve tool to get it out.
10-18-2007 12:06 PM
leejoy great advice guys - thanks

I will do as you say. If I break something or damage something it will be your fault and you will have to come over and fix it for me. I'll supply beer and pizza.

Lee
10-18-2007 11:54 AM
302 Z28
Quote:
Originally Posted by engineczar
To go along with what BBC has said when your doing a cylinder make sure the piston on the cylinder you're doing is at top dead center, that way if something happens the valve will only drop until it hits the piston and you won't lose it down the cylinder.
The compressed air will drive the piston down to bottom dead center unless you have it in gear (standard trans). If it's an automatic there is no way to keep the piston at TDC short of some mechanical means. The piston not being at TDC has never been a problem for me as many as I have changed over the years. Also give each valve retainer a smack with a hammer before you start, it will make the retainers easier to get out.

Vince
10-18-2007 11:37 AM
454C10 do you have an air compressor with a storage tank?
10-18-2007 11:27 AM
engineczar To go along with what BBC has said when your doing a cylinder make sure the piston on the cylinder you're doing is at top dead center, that way if something happens the valve will only drop until it hits the piston and you won't lose it down the cylinder.
10-18-2007 10:46 AM
BBCMudbogger 1. No need to remove the heads

2. You can get a fitting that has spark plu threads on one end and an air connection on the other compressed air holds up the valve

3.Buy a spring height checker....its a micrometer like deal to measure installed height. Summit should have them.

4.You will need a spring compresser that uses the rocker arm stud kinda like a prybar.

5. Inspect the retainers for wear but there shouldnt be any....no need to buy new retainers and locks

6. Its an easy thing to do common sense should guide you through if you have any mechanical aptitude.
10-18-2007 08:38 AM
leejoy
Removing-Reinstalling Valve Springs - Help

guys help

I may need to do a valve spring swap on my BBC. I've never done this. The engine is installed in my car. I am not pulling the engine out.

questions:


1) must I remove the heads from the engine or can I leave them in place. I'd really like to avoid removing the heads if possible, and leave them in place while the springs are replaced.

2) if I can leave the heads installed - how do I prevent the valves from falling into the cylinders when the springs/retainers are removed

3) how do I measure the installed spring height for the new valves - how do I know how much to shim them

4) which spring compressor removal tools are best for my application. are there some that will work with the heads installed on the motor.

5) the springs and hardware were installed 2 years ago and have less than 500 miles on the. can I reuse the retainers/locks or get new ones

6) am I in way over my head and bring them to my engine builder shop and have them do it instead of me - or is that not necessary. I'm very handy and good at working on cars but have never done valve springs.


thanks


Lee

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.