Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> MOnte carlo 79 rear end?
User Name
Password
lost password?   |   register now

Thread: MOnte carlo 79 rear end? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-22-2007 09:08 AM
schnitz
Quote:
Originally Posted by jimfulco
That's backwards. Two turns of the tire, and count driveshaft revs. You don't really need two people. I just position the valve stem at the 6:00 position, and I can feel it when it's back at 6:00 the second time.

Oops. I type corrected. Thanks Jim.


In a while, Chet.
11-22-2007 12:08 AM
jimfulco
Quote:
Originally Posted by schnitz

7. Spin the drive shaft two full rotations and count the number of times the marking on the tire spins.
That's backwards. Two turns of the tire, and count driveshaft revs. You don't really need two people. I just position the valve stem at the 6:00 position, and I can feel it when it's back at 6:00 the second time.
11-17-2007 02:11 PM
schnitz
Quote:
Originally Posted by DHMag
quickest way is to check the code on the axle tube. or pull the diff cover off and read the pinion gear, it will have tooth counts on it for both the ring and pinion. ex: 41 ring gear teeth/17 pinion gear teeth = 2.41 ratio

Not if you live in the salt /rust belt LOL! I've only once been able to find the axle code on anything that old (or older and sometimes even newer) that was just covered in rust. But, I do like the idea of pulling the cover and counting the number of teeth. That also gives you an excuse to change the differential's gear lube.



In a while, Chet.
11-16-2007 11:54 PM
DHMag quickest way is to check the code on the axle tube. or pull the diff cover off and read the pinion gear, it will have tooth counts on it for both the ring and pinion. ex: 41 ring gear teeth/17 pinion gear teeth = 2.41 ratio
11-16-2007 10:44 AM
schnitz
Quote:
Okay, guys - I know this has to have been answered a million times, but I can't find it here anywhere right now. I'm trying to determine my 8" Ford ratio. With both wheels off the ground, I turn the axle and get 1.33 turns of the axle for each full turn of the u-joint! Now, I've heard of economy gears, but that's ridiculous.

I was told to take the rear end cover off and mark a tooth both on the rack and pinion gears with something (piece of tape or scratch with awl). and count the number of teeth for both of the gears.

re: Figuring rear axle ratio
It's a characteristic of non-posi rears. The wheel on the other side was probably turning the other way. They don't always turn the same amount as the one you have your hand on, either, so make sure it's immobile before you count. Then turn the tire TWO full turns while you count the drive shaft revolutions.

The above was copy-pasted from assorted postings from the first link I gave.

The following is not a 100% foolproof method, and will not get an "exact" numeric figure, but will get you very close. Basically, what you need to do is as follows. I plotted this out so I can make it easy for anyone to duplicate.

1. Park the car on a flat, level surface. Block the front and back of each of your front tires, and do the same to one of the rear tires.

2. Raise the unblocked side of the rear end (axle) of your car and firmly and securely supported on a jack stand. Never leave it supported on just the floor jack, that is very unsafe, and can result in serious injury or even death.

3. Put the car it neutral (engine off).

4. Mark the universal joint at one of the 4 bolts that hold the caps to the rear end. You can use a small piece of masking tape and place it over one of the 4 bolt heads.

5. Rotate the tire until you get the mark on the bolt cap to an easily identified and repeatable location on the rear end center section (the "pumpkin" in the middle of the axle). You can mark the pumpkin if you want to. The important thing to remember is to have a repeatable mark to stop on for easy reference.

6. Place a mark on the raised tire, running from the rim to the tread surface, running straight up at the 12:00 position. I use a helper (my "helper" is my wife) for the next step. It helps to have an extra set of eyes, but this can be done alone, just take your time and go slowly.

7. Spin the drive shaft two full rotations and count the number of times the marking on the tire spins.

If the tire spins roughly 2 and 3/4 revolutions, you will have a 2.73 axle ratio. Three and almost a half revolutions will give you a 3.42 rear ratio, and a spun tire of 3 and 3/4 revolutions will give you an approximate ratio of 3.73. By the same way, a 4.11 ratio would have the tire spin just over 4 times around to two times around by the marking on the bolt cap on the universal joint.

My '78 Monte Carlo had a factory ratio of 2.29 (about 2 and a third of a tire rotation).

Hopefully I didn't make this as clear as mud, and it helps you out.



In a while, Chet.
11-16-2007 07:25 AM
rockabilly66
Hi

I need to know the gear ratio
thanks
11-15-2007 09:00 AM
schnitz Just did a quick search to possibly help in what you're looking for. Try here , here, or here.


Maybe you'll find what you are looking for in one of those links to existing threads on this forum. Hope it helps.


In a while, Chet.
11-15-2007 08:48 AM
schnitz What exactly do you want to know? Gear ratio? How to upgrade to rear disc brakes? How to repair/rebuild it? How to swap to steeper gears? We'll need some details of what you want before we can help.


In a while, Chet.
11-15-2007 07:03 AM
rockabilly66
MOnte carlo 79 rear end?

hi
Where can I find info of my montecarlo 79 reaer end, It's a v6 231 T top.
thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.